Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD)
RM37H0E _54 Brake _096747 BRAKE SYSTEM (OTHER) _0454023 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

HINT:
·

Inspect and adjust the brake pedal height with the floor carpet folded back.

·

Perform the inspection from the service hole in the dash panel insulator.



a.

Check the brake pedal height.

i.

Measure the shortest distance between the brake pedal pad surface and front floor footrest as shown in the illustration.

C447612C01
2.25,1.865 2.25,2.115 2.25,2.115 2.5,2.115 true 1.083,1.698 1.083,2.198 1.083,2.198 1.333,2.198 true 5.594,1.458 5.76,0.958 5.76,0.958 6.01,0.958 true 2.552,2.052 2.802,2.219 0.25,0.167 10 true *1 1.198,1.375 1.406,1.552 0.208,0.177 10 true *a 1.385,2.135 1.635,2.302 0.25,0.167 10 true *b 2.833,1.167 3.083,1.333 0.25,0.167 10 true *c 5.417,2.167 5.625,2.344 0.208,0.177 10 false *a 6.063,0.896 6.313,1.063 0.25,0.167 10 false *1
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Front Floor Footrest
*c 41 mm (1.61 in.) - -
V100145

Service Hole - -


Brake Pedal Height from Front Floor Footrest:

184.9 to 194.9 mm (7.28 to 7.67 in.)


If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.



b.

Adjust the push rod length.

i.

Remove the instrument panel safety pad sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


ii.

Remove the steering column assembly.

for Manual Tilt and Manual Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>REMOVAL

for Power Tilt and Power Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL


iii.
C447613C01
1.969,0.885 1.969,0.469 1.969,0.469 2.135,0.469 true 1.979,1.083 2.396,0.75 2.396,0.75 2.563,0.75 true 2.188,0.406 2.521,0.656 0.333,0.25 10 false *1 2.615,0.688 2.948,0.938 0.333,0.25 10 false *2 1.833,3.927 2.146,4.083 0.313,0.156 10 false *a
*1 Lock Nut
*2 Stop Light Switch Assembly
*a Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


iv.

Loosen the lock nut and adjust the brake pedal height by turning the push rod to achieve the correct height.

Brake Pedal Height from Front Floor Footrest:

184.9 to 194.9 mm (7.28 to 7.67 in.)



v.

Tighten the lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


vi.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION


vii.

Install the steering column assembly.

for Manual Tilt and Manual Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>INSTALLATION

for Power Tilt and Power Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>INSTALLATION


viii.

Install the instrument panel safety pad sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION



Hide 89510D 2.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

Hide 4.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C09
2.167,1.563 2.469,1.781 0.302,0.219 10 false *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the brake pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 5.INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
·

Inspect and adjust the brake pedal height with the floor carpet folded back.

·

Perform the inspection from the service hole in the dash panel insulator.



a.

With the ignition switch on (READY), depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

C447612C01
2.25,1.865 2.25,2.115 2.25,2.115 2.5,2.115 true 1.083,1.698 1.083,2.198 1.083,2.198 1.333,2.198 true 5.594,1.458 5.76,0.958 5.76,0.958 6.01,0.958 true 2.552,2.052 2.802,2.219 0.25,0.167 10 true *1 1.198,1.375 1.406,1.552 0.208,0.177 10 true *a 1.385,2.135 1.635,2.302 0.25,0.167 10 true *b 2.833,1.167 3.083,1.333 0.25,0.167 10 true *c 5.417,2.167 5.625,2.344 0.208,0.177 10 false *a 6.063,0.896 6.313,1.063 0.25,0.167 10 false *1
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Front Floor Footrest
*c 41 mm (1.61 in.) - -
V100145

Service Hole - -


Brake Pedal Reserve Distance from Front Floor Footrest at 500 N (51 kgf, 112.4 lbf):

105 mm (4.13 in.) or more