Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for LHD)
RM37H0E _54 Brake _096747 BRAKE SYSTEM (OTHER) _0454023 BRAKE PEDAL(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C451684N01
5.667,2.167 5.667,1.75 5.667,1.75 6,1.75 false 4.229,3.417 4.646,3.417 false 4.75,4.583 5.333,4.583 false 2.833,1.167 2.833,0.5 2.833,0.5 3.083,0.5 false 6.052,1.625 6.385,1.958 0.333,0.333 18 false 1 4.708,3.292 5.042,3.625 0.333,0.333 18 false 2 5.385,4.458 5.719,4.792 0.333,0.333 18 false 3 3.135,0.375 3.469,0.708 0.333,0.333 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING COLUMN ASSEMBLY 45250 - - -
2 FRONT COMPARTMENT MAIN WIRE 82111C - - -
3 DISCONNECT BRAKE PEDAL SUPPORT ASSEMBLY 47110 - - -
4 INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY - - - -

C451678N01
1.219,4.344 1.385,4.344 false 4.333,3 4.333,3.5 4.333,3.5 4.5,3.5 false 4.333,3 4.5,3 false 4.333,0.333 4.583,0.333 false 0.917,2.75 1.167,2.75 false 0.667,1.385 0.667,1.719 0.667,1.719 0.833,1.719 false 2.833,4 3.417,4 false 5.417,4.917 5.75,4.917 false 1.75,1.031 1.75,0.781 1.75,0.781 1.917,0.781 false 4.729,1.417 5.146,1.417 false 3.146,1.417 3.479,1.667 0.333,0.25 10 false x 4 5.125,2.563 5.458,2.813 0.333,0.25 10 false x 2 4.854,3.417 5.188,3.75 0.333,0.333 18 false 5 4.635,0.208 4.969,0.542 0.333,0.333 18 false 6 1.219,2.625 1.552,2.958 0.333,0.333 18 false 7 1.917,4.25 2.25,4.583 0.333,0.333 18 false 8 1.75,4.271 2.083,4.521 0.333,0.25 10 false ● 0.885,1.594 1.219,1.927 0.333,0.333 18 false 10 3.469,3.875 3.885,4.208 0.417,0.333 18 false 11 5.802,4.792 6.219,5.125 0.417,0.333 18 false 12 1.969,0.719 2.302,0.969 0.333,0.25 10 false ● 5.198,1.292 5.531,1.708 0.333,0.417 18 false 9 1.708,3.271 2.042,3.521 0.333,0.25 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
6 BRAKE PEDAL RETURN SPRING 47101A - - -
7 STOP LIGHT SWITCH ASSEMBLY 84340 - - -
8 STOP LIGHT SWITCH MOUNTING ADJUSTER 84345 (Click here) - -
9 BRAKE PEDAL SUPPORT REINFORCEMENT 55179 - - -
10 PUSH ROD PIN 47264A - - -
11 REMOVE BRAKE PEDAL SUPPORT ASSEMBLY 47110 - - -
12 BRAKE PEDAL PAD 47121 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake pedal support assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Brake pedal stroke sensor assembly*

·

Brake pedal*


Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
Brake pedal stroke sensor assembly adjustment Electronically controlled brake system malfunctions
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



PROCEDURE

Hide 45250 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 82111C 2.DISCONNECT FRONT COMPARTMENT MAIN WIRE

a.
C451673


Hide 47110 3.DISCONNECT BRAKE PEDAL SUPPORT ASSEMBLY

a.
C451674


Hide 4.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 89510D 5.REMOVE BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

Click here(Click here)

Hide 47101A 6.REMOVE BRAKE PEDAL RETURN SPRING

a.
C451675


Hide 84340 7.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 84345 8.REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

Z101186

Click here(Click here)

Hide 55179 9.REMOVE BRAKE PEDAL SUPPORT REINFORCEMENT

a.
C451676


Hide 47264A 10.REMOVE PUSH ROD PIN

a.
C451682


Hide 47110 11.REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

a.
C451677


Hide 47121 12.REMOVE BRAKE PEDAL PAD

a.
C451689