Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM37H0E _54 Brake _096747 BRAKE SYSTEM (OTHER) _0454027 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C452507N01
3.917,2.167 4.583,2.167 false 4.635,2.042 4.969,2.542 0.333,0.5 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE MASTER CYLINDER WITH PUMP ASSEMBLY 47200L - - -

C452508N01
3,4.292 3,4.708 3,4.708 3.25,4.708 false 4.417,5.115 4.417,5.365 4.417,5.365 4.667,5.365 false 6.083,1.021 6.083,0.688 6.083,0.688 6.333,0.688 false 1.25,2.771 1.25,2.438 1.25,2.438 1.417,2.438 false 0.833,2.667 0.833,3.167 0.833,3.167 1,3.167 false 3.302,4.583 3.552,4.917 0.25,0.333 18 false 2 4.979,5.26 5.229,5.594 0.25,0.333 18 false 3 6.385,0.563 6.635,0.896 0.25,0.333 18 false 4 1.469,2.375 1.719,2.625 0.25,0.25 10 false *1 1.052,3.104 1.302,3.354 0.25,0.25 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

2 NO. 2 RESERVOIR HOSE - - - -
3 NO. 1 BRAKE ACTUATOR TUBE - (Click here) - -
4 BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY - - - -

*1 BRAKE BOOSTER PUMP BUSHING *2 BRAKE ACTUATOR CASE COLLAR

C451661N01
1.583,2.083 1.583,2.333 1.583,2.333 1.833,2.333 false 5,2.583 5,2.917 5,2.917 5.25,2.917 false 3,3.031 3.333,3.031 false 2.219,2.219 2.469,2.635 0.25,0.417 18 false 5 5.594,2.802 5.844,3.219 0.25,0.417 18 false 6 2.781,2.906 3.031,3.323 0.25,0.417 18 false 7 6.01,2.594 6.344,2.844 0.333,0.25 10 false x 2 3.667,3.375 4,3.625 0.333,0.25 10 false x 2 0.25,0.25 0.583,0.5 0.333,0.25 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 2 WIRE CLAMP BRACKET - (Click here) - -
6 NO. 2 BRAKE POWER SUPPLY BRACKET - (Click here) - -
7 NO. 3 BRAKE POWER SUPPLY BRACKET - (Click here) - -

*A for LHD - -

C447292N03
4.969,2.583 4.969,3.083 4.969,3.083 5.302,3.083 false 2.917,2.625 3.333,2.625 false 1.115,0.833 1.615,0.833 1.615,0.833 1.615,1.083 false 5.688,3.01 6.021,3.344 0.333,0.333 18 false 6 2.74,2.5 3.073,2.833 0.333,0.333 18 false 7 0.927,0.719 1.26,1.052 0.333,0.333 18 false 5 6.021,2.615 6.354,2.948 0.333,0.333 10 false x 2 3.667,3.417 4,3.667 0.333,0.25 10 false x2 0.25,0.25 0.583,0.583 0.333,0.333 10 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 2 WIRE CLAMP BRACKET - (Click here) - -
6 NO. 2 BRAKE POWER SUPPLY BRACKET - (Click here) - -
7 NO. 3 BRAKE POWER SUPPLY BRACKET - (Click here) - -

*A for RHD - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake booster with accumulator pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
No. 1 Skid control ECU (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)

CAUTION:
for LHD:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



CAUTION / NOTICE / HINT

NOTICE:
·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·
C453035C01
0.688,0.5 0.938,0.5 false 0.75,1 1,1 false 0.833,1.5 1.083,1.5 false 1.031,1.833 1.281,1.833 false 2.667,1.833 2.917,1.833 false 2.292,1.5 2.458,1.417 2.458,1.417 2.625,1.417 false 2.375,0.667 2.625,0.667 false 1.719,0.99 1.885,0.406 1.885,0.406 2.052,0.406 true 2.677,0.604 3.01,0.854 0.333,0.25 10 false *a 0.573,0.938 0.906,1.188 0.333,0.25 10 false *b 2.969,1.771 3.219,2.021 0.25,0.25 10 false *c 2.677,1.354 2.927,1.604 0.25,0.25 10 false *d 0.51,0.438 0.844,0.604 0.333,0.167 10 false *e 0.688,1.438 0.938,1.688 0.25,0.25 10 false *f 2.094,0.344 2.344,0.594 0.25,0.25 10 false *g 0.865,1.771 1.198,2.021 0.333,0.25 10 false *h
*a No. 1 Skid Control ECU
*b No. 1 Reservoir Hose and No. 2 Reservoir Hose
*c Master Cylinder Push Rod Clevis
*d Boot
*e Brake Master Cylinder Reservoir
*f No. 1 Brake Actuator Tube
*g No. 1 Wire Clamp Bracket
*h Brake Booster with Accumulator Pump Assembly


Do not carry the brake master cylinder with pump assembly by the parts shown in the illustration.



PROCEDURE

Hide 47210L 1.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Hide 2.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C451652


Hide 3.REMOVE NO. 1 BRAKE ACTUATOR TUBE

a.
C451654N01
0.417,0.073 0.698,0.427 0.281,0.354 18 false i

i.

Using a union nut wrench, remove the No. 1 brake actuator tube.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.





Hide 4.REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.

for LHD:

C451656


b.

for RHD:

C447285


Hide 5.REMOVE NO. 2 WIRE CLAMP BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 2 wire clamp bracket is necessary.



a.

for LHD:

C451658N01
0.417,0.063 0.75,0.396 0.333,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 2 wire clamp bracket.



b.

for RHD:

C447286N01
0.615,0.229 1.365,0.646 0.75,0.417 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 2 wire clamp bracket.



Hide 6.REMOVE NO. 2 BRAKE POWER SUPPLY BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 2 brake power supply bracket is necessary.



a.
C451657N01
0.417,0.052 0.833,0.385 0.417,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 2 brake power supply bracket.



Hide 7.REMOVE NO. 3 BRAKE POWER SUPPLY BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake power supply bracket is necessary.



a.
C451659N01
0.417,0.052 1,0.385 0.583,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 3 brake power supply bracket.