Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR OPENER SYSTEM
RM37H0E _59 Vehicle Exterior _095314 DOOR / HATCH _0453655 LUGGAGE COMPARTMENT DOOR OPENER SYSTEM J

DOOR / HATCH  LUGGAGE COMPARTMENT DOOR OPENER SYSTEM  Luggage Compartment Door Opener does not Operate Using Cabin Switch  


DESCRIPTION

The luggage door opening switch assembly signal is sent to the main body ECU (multiplex network body ECU). If the luggage compartment door opener system does not operate with the luggage door opening switch assembly operation, there may be a malfunction in the circuit of the luggage door opening switch assembly.

WIRING DIAGRAM

E456444E01
4.885,1.896 5.344,2.094 0.458,0.198 10 false D14 4.885,2.083 6.521,2.438 1.635,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 5.24,1.021 5.698,1.219 0.458,0.198 10 false TSW 1.198,1.646 3.729,1.906 2.531,0.26 10 false Luggage Door Opening Switch Assembly 4.958,0.906 5.115,1.104 0.156,0.198 10 false 4 3.521,0.906 3.677,1.104 0.156,0.198 10 false 5 1.479,0.906 1.635,1.104 0.156,0.198 10 false 2 1.677,0.917 1.833,1.115 0.156,0.198 10 false L 3.281,0.906 3.438,1.104 0.156,0.198 10 false B 1.198,1.469 1.656,1.667 0.458,0.198 10 false D110

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Trunk/BDoor Open SW Luggage door opening switch assembly signal OFF or ON OFF: Luggage door opening switch assembly signal off
ON: Luggage door opening switch assembly signal on
-
Body Electrical > Main Body > Data List
Tester Display
Trunk/BDoor Open SW
50003 123 93
OK:

The Data List item changes according to the operation of the luggage door opening switch assembly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT LUGGAGE DOOR OPENING SWITCH ASSEMBLY
2.INSPECT LUGGAGE DOOR OPENING SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE LUGGAGE DOOR OPENING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR OPENING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the D110 luggage door opening switch assembly connector.


b.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D110,D14)Location & Routing

Click Connector(D110)Instrument Panel>Instrument Panel Wire>Luggage Door Opening Switch Assembly

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D110-5 (B) - D14-4 (TSW) Always Below 1 Ω
D110-2 (L) - Body ground Always Below 1 Ω
D110-5 (B) or D14-4 (TSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR