Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0447864 TOYOTA MULTI OPERATION TOUCH SYSTEM D

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Using the GTS to enter the "Trouble Codes" screen.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181

b.

Check for DTCs, and then write them down.




CLEAR DTC (CLEAR USING GTS)


a.

Using the GTS, perform the "Clear DTCs".

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

b.

Clear the DTCs.



START DIAGNOSTIC MODE


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Turn the ignition switch to ON.


b.

Display the audio screen.


c.
E443878C01
0.396,0.906 0.552,0.323 0.552,0.323 0.719,0.323 false 0.781,1.344 0.646,1.99 0.646,1.99 0.479,1.99 false 1.01,0.917 1.167,0.333 1.167,0.333 1.333,0.333 false 1.417,0.271 1.729,0.427 0.313,0.156 10 false *a 0.771,0.26 1.083,0.417 0.313,0.156 10 false *b 0.042,0.031 0.354,0.188 0.313,0.156 10 false *1 0.271,1.917 0.583,2.073 0.313,0.156 10 false *c
*1 Multi-display Assembly
*a Upper Right Corner
*b Upper Left Corner
*c Audio screen


Touch the audio screen 5 times in the upper right corner, then 5 times in the upper left corner.



CHECK MODE SCREEN


a.
E438159

Select "Failure Diagnosis" from the "Service Menu" screen.


b.
E438160

Select "System Check" from the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E438161N01
0.656,1.76 0.656,1.115 false 1.146,1.76 1.146,1.115 false 2.042,1.771 2.042,1.604 false 2.625,1.771 2.625,1.604 false 0.583,1.792 0.896,1.99 0.313,0.198 10 false *a 1.073,1.792 1.385,1.99 0.313,0.198 10 false *b 1.969,1.792 2.281,1.99 0.313,0.198 10 false *c 2.552,1.802 2.865,2 0.313,0.198 10 false *d

System check mode screen description

Screen Description
Display Content
*a: Device name list
·

Device Name List displays some of the devices that make up the Toyota multi operation touch system.

·

The names of the components from Device Name List are shown in the following table.


*b: Check result Result codes for all devices are displayed.
*c: Memory clear
·

Present and history DTCs and registered connected device names are cleared.

·

Select "Memory CLR" for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

"Recheck" will dim during a system check.



*a: Device Name List No. 1 Description
Name Component Connection Method
TMOT Integration control sub-assembly -
DCU Radio receiver assembly AVC-LAN communication line
DISP Multi-display assembly AVC-LAN communication line

*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Read the DTCs on the "Unit Check Mode" screen.
NCON The device was previously present, but did not respond in diagnostic mode.
·

Check the power supply circuit of the device.

·

Check the AVC-LAN communication line of the device.


NRES The device responded in diagnostic mode, but gives no DTC information.
·

Check the power supply circuit of the device.

·

Check the AVC-LAN communication line of the device.




b.
E438162N01
0.375,0.667 0.677,0.667 true 0.875,1.865 0.875,1.115 true 1.365,0.615 1.188,0.208 1.188,0.208 0.979,0.208 true 2.917,1.688 3.125,1.688 true 1.958,1.885 1.958,1.031 true 0.813,0.115 1.125,0.313 0.313,0.198 10 false *a 0.198,0.583 0.479,0.781 0.281,0.198 10 false *b 0.771,1.906 1.083,2.104 0.313,0.198 10 false *c 1.885,1.938 2.198,2.135 0.313,0.198 10 false *d 3.167,1.615 3.333,1.833 0.167,0.219 10 false *e

Unit check mode screen description

Screen Description
Display Content
*a: History DTC Diagnostic memory results and stored DTCs are displayed.
*b: Present DTC DTCs output in the service check are displayed.
*c: DTC DTC (Diagnostic Trouble Code)
*d: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
*e: Diagnosis clear Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.

Read the system check result.

i.

If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", no DTCs are output.

·

When "NCON" is displayed for all devices connected via AVC-LAN communication, or when all device names are not displayed, check if there is a short in an AVC-LAN line or device connected to the AVC-LAN. Repair or replace parts as necessary.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>AVC-LAN Circuit

·

When proceeding to view the results of another device, select "Back" to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.







DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E438168

Clear the DTCs

i.

Select "Memory CLR" for 3 seconds.


ii.

Check that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, use the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.





b.
E438169

Recheck

i.

Select "Recheck".


ii.
E438170

Check that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the ignition switch off.