Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM37H0E _56 Audio / Visual / Telematics _095262 TELEMATICS _0447865 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B153711  Telephone Sub Antenna Circuit Short to Ground  B153713  Telephone Sub Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone sub antenna circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B153711 Telephone Sub Antenna Circuit Short to Ground Telephone antenna (sub) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telematics Transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly


Telematics A
B153713 Telephone Sub Antenna Circuit Open Telephone antenna (sub) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telematics Transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly


Telematics A

WIRING DIAGRAM

E364289E44
2.063,2.406 3.271,2.823 1.208,0.417 10 false Navigation Antenna Assembly 3.708,2.667 4.625,3.031 0.917,0.365 10 false Antenna Cord Sub-assembly 5.031,2.552 6.521,2.896 1.49,0.344 10 false Telematics Transceiver 4.719,1.438 5.448,1.875 0.729,0.438 10 false ANT3 3.354,1.427 3.469,1.594 0.115,0.167 10 false A 3.365,1.969 3.479,2.135 0.115,0.167 10 false A 4.792,1.208 5.135,1.448 0.344,0.24 10 false [1] 4.74,1.75 5.177,2.063 0.438,0.313 10 false [1a] 3.365,1.229 3.479,1.396 0.115,0.167 10 false 4 3.333,1.76 3.531,1.927 0.198,0.167 10 false 4a 5.156,1.448 5.646,1.677 0.49,0.229 10 false TELS 4.708,1.969 5.438,2.406 0.729,0.438 10 false ANT3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

a.

Recheck for DTCs.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

None



A

B

2.INSPECT NAVIGATION ANTENNA ASSEMBLY
2.INSPECT NAVIGATION ANTENNA ASSEMBLY

Pre-procedure1

a.
E356744C24
1.375,1.177 1.417,0.833 true 1.438,0.802 1.302,0.323 true 0.135,0.146 0.448,0.344 0.313,0.198 10 false *a 1.198,1.156 1.406,1.385 0.208,0.229 10 false 4a 1.188,0.156 1.396,0.385 0.208,0.229 10 false 4
*a Component without harness connected
(Navigation Antenna Assembly)


Remove the navigation antenna assembly.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 9 to 11 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna connector from the navigation antenna assembly.


b.

Disconnect the antenna connector from the telematics transceiver.


Procedure1

a.
E427068C25
1.479,0.115 1.844,0.385 0.365,0.271 1.469,1.698 1.885,2 0.417,0.302 2.146,0.844 2.5,0.333 2.5,0.333 2.698,0.333 true 1.833,2.771 2.188,2.26 2.188,2.26 2.385,2.26 true 1.021,2.604 1.208,2.604 1.208,2.604 1.646,2.781 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 2.771,0.25 3.083,0.448 0.313,0.198 10 false 4a 2.448,2.188 2.76,2.385 0.313,0.198 10 false [1a] 0.635,2.521 1.031,2.813 0.396,0.292 10 false TELS 1.635,0.167 1.948,0.365 0.313,0.198 10 false A 1.51,1.76 1.938,1.979 0.427,0.219 10 false ANT3 0.167,1.792 0.479,1.99 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - ANT3-[1] (TELS) Always Below 1 Ω
A-4a - ANT3-[1a] Always Below 1 Ω
A-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT