Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD (for Instrument Panel)
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0448166 RADIO ANTENNA CORD(for Instrument Panel) A

AUDIO / VIDEO  RADIO ANTENNA CORD(for Instrument Panel)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E458248N01
1.198,1.938 6.427,3.708 5.229,1.771 5.042,1.01 5.583,1.01 false 5.604,2.833 5.958,2.833 false 2.208,2.927 2.594,2.927 false 3.083,1.927 3.083,3.677 false 6.531,0.198 6.792,0.198 false 4.875,1.948 4.875,3.698 false 3.958,2.917 4.344,2.917 false 6.333,0.073 6.51,0.427 0.177,0.354 18 false 1 5.698,0.865 5.979,1.219 0.281,0.354 18 false 2 2.646,2.792 2.927,3.146 0.281,0.354 18 false 3 1.281,1.958 1.656,2.198 0.375,0.24 12 false *A 3.135,1.969 3.51,2.208 0.375,0.24 12 false *B 6.031,2.698 6.313,3.052 0.281,0.354 18 false 3 4.417,2.781 4.698,3.135 0.281,0.354 18 false 3 4.927,1.969 5.302,2.208 0.375,0.24 12 false *C

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 INSTRUMENT PANEL SAFETY PAD ASSEMBLY - - - -
3 ANTENNA CORD SUB-ASSEMBLY 86101 - - -

*A w/ Telematics Transceiver, Navigation System *B w/o Telematics Transceiver, Navigation System
*C w/o Telematics Transceiver, w/ Navigation System - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the antenna cord sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 86101 3.REMOVE ANTENNA CORD SUB-ASSEMBLY

a.

w/ Telematics Transceiver, Navigation System:

E455463


b.

w/o Telematics Transceiver, Navigation System:

E461227


c.

w/o Telematics Transceiver, w/ Navigation System:

E455507