1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT
| *a | 2 m (6.56 ft.) |
| *b | 1.5 m (4.92 ft.) |
|
Do not place any metal objects in this area |
|
Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area |
Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.
Metal objects that have a height of 50 mm (1.97 in.) or less do not affect adjustment within 2 m (6.56 ft.) from the front of the vehicle.
Check the levelness of the ground.
| *a | 1.5 m (4.92 ft.) |
|
Levelness Check Point |
Check the levelness of the ground at the 3 points shown in the illustration.
Place the level on each levelness check point and check that the air bubble of the level is centered.
Adjust the tire inflation pressure to the specified pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Clean the front emblem or millimeter wave radar sensor assembly.
Visually inspect the front of the vehicle.
Confirm that there is no damage or deformation.
Visually inspect the front bumper assembly and stays.
Confirm that there is no damage or deformation.
2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY
| *a | SST (Flat Surface Target) |
| *b | SST (Stand) |
Adjust SST (flat surface target) height.
Check that SST (flat surface target) has no damage or deformation.
Check that SST (flat surface target) is assembled correctly.
Check that SST (flat surface target) has no looseness or wobble.
| *a | Handle |
| *b | Scale |
| *c | Height Reference Line |
Loosen the top and bottom handles of SST (stand), and while checking the included scale, adjust the height of SST (flat surface target) as shown in the illustration so that its height reference line is at the same height as the millimeter wave radar sensor assembly, then re-tighten the top and bottom handles.
Adjust SST (flat surface target) so that its center is aligned with the millimeter wave radar sensor assembly (center of emblem).
Height adjustment can be performed using the scale included with SST (flat surface target).
692 mm (2.27 ft.)
Place SST (flat surface target).
Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.
| *a | String | *b | Weight |
| *c | Center | *d | Bilateral Symmetry |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.
| *a | String | *b | Weight |
| *c | Center | *d | Bilateral Symmetry |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
When using a laser line marker:
Do not look directly into the laser beam.
Press the laser mode button on the laser line marker to activate the laser line emitters.
| *a | Ground Marking Point (Cross Portion) |
Align the laser beam ground marking point (cross portion) with point B.
Align the center of the target panel with point A, and set the target panel so that it faces forward.
| *a | Center Line | *b | Target Panel |
Adjust the position of the laser line marker so that the laser beam is aligned with the center line of the target panel.
| *a | Tape Measure |
Extend a tape measure at least 1500 mm (4.92 ft.) in length from point B, and set the tape measure in place.
| *a | Tape Measure |
| *b | Tape |
| *c | 1500 mm (4.92 ft.) |
Mark point C at a distance of 1500 mm (4.92 ft.) from point B, and apply a 300 mm (11.81 in.) piece of tape alongside the tape measure so that the tape extends 150 mm (5.91 in.) to the front and rear of point C.
When not using a laser line marker:
Using tape and a string, create a line that connects point B to point A and extends at least 1500 mm (4.92 ft.) beyond the front center point of the vehicle.
| *a | String | *b | Tape |
| *c | 1500 mm (4.92 ft.) | - | - |
Make sure the string is taut when securing it with tape.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C (SST (flat surface target) placement position) at a position 1500 mm (4.92 ft.) from point B.
Position SST (flat surface target) so that it is aligned with the target position line and the mark-off line is aligned with point C as shown in the illustration.
| *a | SST (Stand) | *b | Mark-off Line |
| *c | Reference Line | - | - |
Front Beam Axis Adjustment:
Close all of the doors.
Ensure that nobody enters the adjustment area during the adjustment.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Do not turn off the GTS or ignition switch.
If the vehicle moves or is shaken during beam axis adjustment such as during strong winds or a door is opened or closed, perform the adjustment again.
| Tester Display |
|---|
| Front Beam Axis Adjustment |
Press "Next".
Perform the adjustment according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.
Press "Exit" to finish front beam axis adjustment.
Front Beam Axis Misalignment Reading:
Close all of the doors.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Ensure that nobody enters the adjustment area during the adjustment.
Do not turn off the GTS or ignition switch.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
Press "Next".
Perform the adjustment according to the display on the GTS.
| Vertical | -0.5 to 0.5 deg. |
| Horizontal | -0.5 to 0.5 deg. |
If the result is not as specified, perform beam axis adjustment again.
Front Radar Acceleration Sensor Calibration:
| Tester Display |
|---|
| Front Radar Acceleration Sensor Calibration |
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
After beam axis adjustment completes, clear the following system vehicle control history entries.
Clear vehicle control history (Dynamic radar cruise control system).
Clear vehicle control history (Front camera system).
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lane tracing assist system).
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Front radar sensor system).
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Pre-collision system).
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lighting system).
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>VEHICLE CONTROL HISTORY