Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front)
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0454704 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B611717N15
3.313,1.958 3.583,2.292 3.583,2.292 3.969,2.292 false 4.01,2.125 4.563,2.479 0.552,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ULTRASONIC SENSOR CUSHION SET 89305 - - -

B601963N02
2,0.115 4.417,1.083 2.417,0.969 5.417,1.75 7.083,3.333 1.667,1.583 2.833,4.083 3.417,4.083 false 5.74,2.188 5.99,2.188 false 2.396,0.615 2.646,0.615 false 3.479,0.854 3.729,0.854 false 3.042,1.323 3.375,1.323 false 2.302,1.74 2.24,1.74 2.24,1.74 2.24,1.406 false 3.177,1.896 3.51,1.896 false 4.677,2.302 5.01,2.302 false 4.76,3.552 4.677,3.552 4.677,3.552 4.677,3.219 false 6.313,3.073 6.229,3.073 6.229,3.073 6.229,2.74 false 4.156,2.729 3.99,2.729 3.99,2.729 3.99,2.396 false 6.458,0.24 6.792,0.24 false 3.531,3.958 3.813,4.313 0.281,0.354 18 false 7 3.583,1.76 3.865,2.115 0.281,0.354 18 false 6 4.219,2.594 4.5,2.948 0.281,0.354 18 false 6 3.438,1.188 3.719,1.542 0.281,0.354 18 false 5 5.083,2.177 5.365,2.531 0.281,0.354 18 false 5 6.063,2.063 6.344,2.417 0.281,0.354 18 false 4 3.813,0.719 4.094,1.073 0.281,0.354 18 false 4 2.979,0.521 3.25,0.813 0.271,0.292 10 false ● 2.667,1.646 2.938,1.938 0.271,0.292 10 false ● 5.094,3.458 5.365,3.75 0.271,0.292 10 false ● 6.656,2.969 6.927,3.26 0.271,0.292 10 false ● 2.802,1.594 3.083,1.948 0.281,0.354 18 false 3 5.229,3.427 5.51,3.781 0.281,0.354 18 false 3 3.104,0.479 3.385,0.833 0.281,0.354 18 false 2 6.76,2.917 7.042,3.271 0.281,0.354 18 false 2 2.073,0.167 2.448,0.406 0.375,0.24 12 false *A 5.5,1.802 5.875,2.042 0.375,0.24 12 false *A 6.292,0.125 6.573,0.479 0.281,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

2 FRONT SIDE ULTRASONIC SENSOR RETAINER 89C48F (Click here) - -
3 FRONT CORNER ULTRASONIC SENSOR RETAINER 89C48D (Click here) - -
4 FRONT SIDE ULTRASONIC SENSOR 89341M - - -
5 FRONT CORNER ULTRASONIC SENSOR 89341K - - -
6 FRONT CENTER ULTRASONIC SENSOR 89341L - - -
7 FRONT BUMPER ASSEMBLY - - - -
8 PERFORM CALIBRATION - - - (Click here)

*A w/ Advanced Park - -
● Non-reusable part - -

PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET

Hide 89C48F 2.INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park)

a.
B599554C02
2.76,2.521 2.927,2.688 2.927,2.688 3.177,2.688 false 0.417,0.292 0.698,0.646 0.281,0.354 18 false i 4.042,0.302 4.323,0.656 0.281,0.354 18 false ii 0.406,1.781 0.688,2.135 0.281,0.354 18 false iii 0.427,3.167 0.708,3.521 0.281,0.354 18 false iv 6.021,0.333 6.333,0.531 0.313,0.198 10 false *a 6.656,0.938 6.969,1.135 0.313,0.198 10 false *a 3.229,2.625 3.542,2.823 0.313,0.198 10 false *b 0.406,4.677 0.688,5.031 0.281,0.354 18 false v
*a 30 mm (1.18 in.) *b Mark-off Line
V100144

Installation area - -


i.

Clean the front bumper assembly surface:

1. When reusing the front bumper assembly, remove remaining double-sided tape from the front bumper assembly.

2. Using a heat light, heat the front bumper assembly surface.

Standard Value:
Part Temperature
Front Bumper Assembly 20 to 30°C (68 to 86°F)
Front Side Ultrasonic Sensor Retainer 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper assembly excessively.


3. Remove any remaining double-sided tape from the front bumper assembly and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the front side ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front bumper assembly surface.




ii.

Cover the sensor installation hole from the outside of the bumper with a 30 mm (1.18 in.) square piece of tape.


iii.

Primer application:

1. Apply primer to the front bumper assembly on the installation area of the front side ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front side ultrasonic sensor retainer has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the front bumper assembly and a new front side ultrasonic sensor retainer.

NOTICE:

Do not heat the front side ultrasonic sensor retainer and front bumper assembly excessively.



v.

Install the front side ultrasonic sensor retainer in the position shown in the illustration.

NOTICE:

The application strength of the front side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front bumper assembly.




b.

The orientation for the RH side is the opposite of the LH side.


Hide 89C48D 3.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

a.
B599553C02
2.76,2.521 2.927,2.688 2.927,2.688 3.177,2.688 false 0.417,0.292 0.698,0.646 0.281,0.354 18 false i 4.042,0.302 4.323,0.656 0.281,0.354 18 false ii 0.406,1.781 0.688,2.135 0.281,0.354 18 false iii 0.427,3.167 0.708,3.521 0.281,0.354 18 false iv 6.021,0.333 6.333,0.531 0.313,0.198 10 false *a 6.656,0.938 6.969,1.135 0.313,0.198 10 false *a 3.229,2.625 3.542,2.823 0.313,0.198 10 false *b 0.406,4.677 0.688,5.031 0.281,0.354 18 false v
*a 30 mm (1.18 in.) *b Mark-off Line
V100144

Installation area - -


i.

Clean the front bumper assembly surface:

1. When reusing the front bumper assembly, remove remaining double-sided tape from the front bumper assembly.

2. Using a heat light, heat the front bumper assembly surface.

Standard Value:
Part Temperature
Front Bumper Assembly 20 to 30°C (68 to 86°F)
Front Corner Ultrasonic Sensor Retainer 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper assembly excessively.


3. Remove any remaining double-sided tape from the front bumper assembly and wipe off any tape adhesive residue with cleaner.

4. Clean the installation area surface.

NOTICE:
·

Installing the front corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front bumper assembly surface.




ii.

Cover the sensor installation hole from the outside of the bumper with a 30 mm (1.18 in.) square piece of tape.


iii.

Primer application:

1. Apply primer to the front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.



2. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



iv.

Using a heat light, heat the front bumper assembly and a new front corner ultrasonic sensor retainer.

NOTICE:

Do not heat the front corner ultrasonic sensor retainer and front bumper assembly excessively.



v.

Install the front corner ultrasonic sensor retainer in the position shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:

Apply pressure so that it does not lift up from the front bumper assembly.




b.

The orientation for the RH side is the opposite of the LH side.


Hide 89341M 4.INSTALL FRONT SIDE ULTRASONIC SENSOR (w/ Advanced Park)

Hide 89341K 5.INSTALL FRONT CORNER ULTRASONIC SENSOR

Hide 89341L 6.INSTALL FRONT CENTER ULTRASONIC SENSOR

Hide 7.INSTALL FRONT BUMPER ASSEMBLY