Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095261 NAVIGATION / MULTI INFO DISPLAY _0453794 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation ECU assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position on the map.

The navigation ECU assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C2 Speed Signal Malfunction A difference between the GPS speed and SPD pulse is detected
·

Meter / gauge system

·

Navigation ECU assembly

·

Radio receiver assembly

·

Harness or connector


Navigation System A

WIRING DIAGRAM

E368000E48
2.427,1.104 2.885,1.302 0.458,0.198 10 false 19 2.125,1.229 2.583,1.427 0.458,0.198 10 false +S 4.635,1.104 5.094,1.302 0.458,0.198 10 false 9 4.833,1.208 5.292,1.406 0.458,0.198 10 false SPD 4.552,2.021 5.01,2.219 0.458,0.198 10 false D65 4.552,2.188 6.313,2.49 1.76,0.302 10 false Navigation ECU Assembly 1.031,2.031 1.49,2.229 0.458,0.198 10 false D41 1.021,2.198 3.042,2.542 2.021,0.344 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

B

2.CHECK VEHICLE SENSOR (OPERATION CHECK)
2.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK



b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the No. 2 skid control ECU via CAN communication. Therefore, perform the following procedure inspection referring to values in the Data List of the No. 2 skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS.


HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU ASSEMBLY

NG

3.CHECK COMBINATION METER ASSEMBLY (CHECK OUTPUT WAVEFORM)
3.CHECK COMBINATION METER ASSEMBLY (CHECK OUTPUT WAVEFORM)

Pre-procedure1

a.
E393685C56
1.49,0.344 1.917,0.615 0.427,0.271 0.844,1.281 0.583,0.677 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.583,0.396 2.042,0.594 0.458,0.198 10 false D41 0.5,0.479 0.813,0.677 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.125,3.844 1.281,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Remove the combination meter assembly with the connector(s) still connected.

HINT:

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



b.

Connect an oscilloscope to terminal D41-19 (+S) and body ground.


c.

Turn the ignition switch to ON.


d.

Turn a wheel slowly.


Procedure1

e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal D41-19 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the D65 navigation ECU assembly connector.


b.

Disconnect the D41 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D65,D41)Location & Routing

Click Connector(D65)Instrument Panel>Instrument Panel Wire>Navigation ECU Assembly

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D65-9 (SPD) - D41-19 (+S) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.REPLACE NAVIGATION ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU ASSEMBLY
a.

Replace the navigation ECU assembly with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Procedure1

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

None



A

END (NAVIGATION ECU ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO RECEIVER ASSEMBLY