Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
RM37H0E _55 Steering _095770 STEERING COLUMN _0454949 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B26031C  Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range  


DESCRIPTION

Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B26031C Tilt and Telescopic Manual Switch Circuit Circuit Voltage Out of Range When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU.
·

Tilt and telescopic switch

·

Harness or connector

·

Multiplex tilt and telescopic ECU


Tilt&Telescopic A

WIRING DIAGRAM

C240527E90
4.917,3.875 7.073,4.188 2.156,0.313 10 false Multiplex Tilt and Telescopic ECU 1.458,3.75 3.583,3.906 2.125,0.156 10 false Tilt and Telescopic Switch 3.75,2.646 4.115,2.802 0.365,0.156 10 false MSW 3.906,1 4.125,1.156 0.219,0.156 10 false VC 5.125,2.75 5.49,2.906 0.365,0.156 10 false MSW 5.135,1.094 5.354,1.25 0.219,0.156 10 false VC 0.708,1.979 1.333,2.448 0.625,0.469 10 false Tilt Down 1.573,1.896 2.25,2.458 0.677,0.563 10 false Telescopic Contract 2.448,1.979 2.979,2.281 0.531,0.302 10 false Tilt Up 3.333,1.885 4.031,2.469 0.698,0.583 10 false Telescopic Extend 4.927,1 5.104,1.167 0.177,0.167 10 false 5 4.865,2.646 5.104,2.813 0.24,0.167 10 false 18 4.917,3.688 5.385,3.885 0.469,0.198 10 false D22 1.458,3.563 1.948,3.781 0.49,0.219 10 false D29 4.177,2.646 4.354,2.813 0.177,0.167 10 false 3 4.177,1 4.354,1.167 0.177,0.167 10 false 1

PROCEDURE

1.READ VALUE USING GTS (TILT MANUAL SWITCH UP)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Manual Switch Up Input state of tilt up switch OFF or ON ON: When tilt and telescopic switch up operation performed -
Body Electrical > Tilt&Telescopic > Data List
Tester Display
Tilt Manual Switch Up
50003 406 18

Result:
Result Proceed to
The value of Tilt Manual Switch Up is ON A
The value of Tilt Manual Switch Up is not ON B



A

2.READ VALUE USING GTS (TILT MANUAL SWITCH DOWN)

B

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
2.READ VALUE USING GTS (TILT MANUAL SWITCH DOWN)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Manual Switch Down Input state of tilt down switch OFF or ON ON: When tilt and telescopic switch down operation performed -
Body Electrical > Tilt&Telescopic > Data List
Tester Display
Tilt Manual Switch Down
50003 406 19

Result:
Result Proceed to
The value of Tilt Manual Switch Down is ON A
The value of Tilt Manual Switch Down is not ON B



A

3.READ VALUE USING GTS (TELESCOPIC MANUAL SWITCH SHORT)

B

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
3.READ VALUE USING GTS (TELESCOPIC MANUAL SWITCH SHORT)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Telescopic Manual Switch Short Input state of telescopic contract switch OFF or ON ON: When tilt and telescopic switch short operation performed -
Body Electrical > Tilt&Telescopic > Data List
Tester Display
Telescopic Manual Switch Short
50003 406 20

Result:
Result Proceed to
The value of Telescopic Manual Switch Short is ON A
The value of Telescopic Manual Switch Short is not ON B



A

4.READ VALUE USING GTS (TELESCOPIC MANUAL SWITCH LONG)

B

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
4.READ VALUE USING GTS (TELESCOPIC MANUAL SWITCH LONG)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Telescopic Manual Switch Long Input state oftelescopic extendswitch OFF or ON ON: When tilt and telescopic switch long operation performed -
Body Electrical > Tilt&Telescopic > Data List
Tester Display
Telescopic Manual Switch Long
50003 406 21

Result:
Result Proceed to
The value of Telescopic Manual Switch Long is ON A
The value of Telescopic Manual Switch Long is not ON B



A

5.CLEAR DTC

B

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Tilt&Telescopic > Clear DTCs
50002 406

Result:
Proceed to
NEXT



NEXT

6.CONFIRM DTC
6.CONFIRM DTC
a.

Check for DTCs.

Body Electrical > Tilt&Telescopic > Trouble Codes
50001 406

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

B

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)

Pre-procedure1

a.

Disconnect the D22 multiplex tilt and telescopic ECU connector.


b.

Disconnect the D29 tilt and telescopic switch connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D22,D29)Location & Routing

Click Connector(D22)Instrument Panel>Instrument Panel Wire>Multiplex Tilt & Telescopic ECU

Click Connector(D29)Instrument Panel>Instrument Panel Wire>Tilt & Telescopic Switch

D22-5 (VC) - D29-1 (VC) Always Below 1 Ω
D22-18 (MSW) - D29-3 (MSW) Always Below 1 Ω
D22-5 (VC) or D29-1 (VC) - Body ground Always 10 kΩ or higher
D22-18 (MSW) or D29-3 (MSW) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

Pre-procedure1

a.

Reconnect the D22 multiplex tilt and telescopic ECU connector.


Procedure1

a.
C401145C36
1.458,0.26 1.875,0.5 0.417,0.24 0.927,1.635 1.156,1.146 true 1.156,0.896 0.938,0.542 true 1.542,0.302 2,0.5 0.458,0.198 10 false D22 0.813,0.385 1.271,0.583 0.458,0.198 10 false VC 0.729,1.667 1.188,1.865 0.458,0.198 10 false MSW 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D22)Location & Routing

Click Connector(D22)Instrument Panel>Instrument Panel Wire>Multiplex Tilt & Telescopic ECU

D22-5 (VC) - D22-18 (MSW) Ignition switch ON 4.9 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.INSPECT TILT AND TELESCOPIC SWITCH

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

9.INSPECT TILT AND TELESCOPIC SWITCH

OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE TILT AND TELESCOPIC SWITCH