Home › Steering › STEERING COLUMN › MULTIPLEX TILT AND TELESCOPIC ECU › 2020.11–2021.08
RM37H0E _55 Steering _095770 STEERING COLUMN _0449638 MULTIPLEX TILT AND TELESCOPIC ECU A

STEERING COLUMN  MULTIPLEX TILT AND TELESCOPIC ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C447810N01
3.208,3.083 3.542,3.354 3.542,3.354 3.708,3.354 true 5.927,2.625 6.177,2.99 6.177,2.99 6.344,2.99 true 4.885,1.333 5.219,1.333 true 6.521,0.219 6.854,0.219 true 6.333,0.083 6.615,0.438 0.281,0.354 18 false 1 5.302,1.177 5.677,1.479 0.375,0.302 18 false 4 4.042,3.229 4.323,3.583 0.281,0.354 18 false 2 6.427,2.833 6.74,3.125 0.313,0.292 18 false 3 3.646,2.688 3.927,3.042 0.281,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
2 LOWER STEERING COLUMN COVER 45287 (Click here) - -
3 LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY 73900 - - -
4 MULTIPLEX TILT AND TELESCOPIC ECU 88227 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the multiplex tilt and telescopic ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

Click here(Click here)

Hide 45287 2.REMOVE LOWER STEERING COLUMN COVER

Z101186

Click here(Click here)

Hide 73900 3.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY

Hide 89227 4.REMOVE MULTIPLEX TILT AND TELESCOPIC ECU

a.
C447811N01
0.271,0.083 0.479,0.417 0.208,0.333 18 false i 3.604,0.031 4.104,0.365 0.5,0.333 18 true ii, iii

i.

Disconnect the 2 clamps.


ii.

Disconnect the connector.


iii.

Disengage the 2 claws and guide to remove the multiplex tilt and telescopic ECU from the steering column assembly.