Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM J

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P Position Switch Indicator Circuit  


DESCRIPTION

The shift position indicator (P, R, N, D, Br) ON (indicator illuminates (shift state in park (P), reverse (R), neutral (N), drive (D) or brake (Br)) or OFF (indicator goes off (shift state not in park (P), reverse (R), neutral (N), drive (D) or brake (Br)) is displayed.

The shift position indicator goes off when a system malfunction occurs (not in all cases) and a warning message will also be displayed on the multi-information display.

WIRING DIAGRAM

C450253E01
4.208,2.917 6.115,3.135 1.906,0.219 10 false Shift Control ECU 0.729,2.49 3.094,2.802 2.365,0.313 10 false P Position Switch (Parking Switch) 0.729,2.271 1.188,2.469 0.458,0.198 10 false D17 4.198,2.677 4.656,2.875 0.458,0.198 10 false D93 4.333,1.531 4.948,1.729 0.615,0.198 10 false INDP 4.021,1.531 4.333,1.729 0.313,0.198 10 false 12 2.75,1.51 2.906,1.708 0.156,0.198 10 false 4 2.26,1.625 2.875,1.823 0.615,0.198 10 false IND- 2.24,0.573 2.854,0.771 0.615,0.198 10 false IND+ 2.719,0.458 2.875,0.656 0.156,0.198 10 false 7 4.708,0.719 6.542,0.917 1.833,0.198 10 false ECU-B P NO.2

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.CHECK P POSITION SWITCH (PARKING SWITCH) (CHECK ILLUMINATION)
a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Operate the P position switch (parking switch) and check the illumination status of the P position switch indicator.

Result:
Result Proceed to
P position switch indicator does not go off (remains on) A
P position switch indicator does not illuminate B



d.

Turn the ignition switch off.



A

2.CHECK P POSITION SWITCH (PARKING SWITCH) (CHECK ILLUMINATION)

B

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (PARKING SWITCH) POWER SOURCE CIRCUIT)
2.CHECK P POSITION SWITCH (PARKING SWITCH) (CHECK ILLUMINATION)
a.

Disconnect the D93 shift control ECU connector.


b.

Turn the ignition switch to ON.


c.

Check the illumination status of the P position switch indicator.

Result:
Result Proceed to
Shift position indicator illuminates A
Shift position indicator goes off. B


NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the ignition switch off.


e.

Reconnect the D93 shift control ECU connector.



A

3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P POSITION SWITCH (PARKING SWITCH))

B

3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P POSITION SWITCH (PARKING SWITCH))
a.

Disconnect the D93 shift control ECU connector.


b.

Disconnect the D17 P position switch (parking switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D17)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D93-12 (INDP) or D17-4 (IND-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the D17 P position switch (parking switch) connector.


e.

Reconnect the D93 shift control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (PARKING SWITCH) POWER SOURCE CIRCUIT)
a.

Disconnect the P position switch (parking switch) connector.


C449853C03
0.229,0.875 0.604,1.146 0.375,0.271 1.896,1.198 2.781,1.188 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.302,0.948 0.76,1.146 0.458,0.198 10 false D17 2.854,1.135 3.323,1.365 0.469,0.229 10 false IND+
*a Front view of wire harness connector
(to P Position Switch (Parking Switch))


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D17)Location & Routing

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D17-7 (IND+) - Body ground Always 9 to 14 V


NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the ignition switch off.


e.

Reconnect the P position switch (parking switch) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT P POSITION SWITCH (PARKING SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT P POSITION SWITCH (PARKING SWITCH)
a.
C449852C02
1.479,1.49 0.75,1.49 true 1.969,1.188 2.604,1.198 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 0.188,1.438 0.99,1.635 0.802,0.198 10 false IND+ (+) 2.667,1.125 3.281,1.323 0.615,0.198 10 false IND- (-)
*a Component without harness connected
(P Position Switch (Parking Switch))


Remove the P position switch (parking switch).


b.

Apply battery voltage between the terminals specified in the table below and check the indicator.

Result:
Condition Specified Condition
Auxiliary battery voltage applied between terminals 7 (IND+) and 4 (IND-) Comes on



c.

Install the P position switch (parking switch).


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT POSITION INDICATOR)

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - SHIFT POSITION INDICATOR)
a.

Disconnect the D93 shift control ECU connector.


b.

Disconnect the D17 P position switch (parking switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D17)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switch

D93-12 (INDP) - D17-4 (IND-) Always Below 1 Ω



d.

Reconnect the D17 P position switch (parking switch) connector.


e.

Reconnect the D93 shift control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR