After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.
Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the ignition switch to ON.
With the brake pedal depressed, move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| None of the DTCs are output. | A |
| Any of the DTCs are output. | B |
Turn the ignition switch off.
A
B
Turn the ignition switch to ON.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| BATT Voltage for Gear Shift Control Module |
| Result | Proceed to |
|---|---|
| BATT Voltage for Gear Shift Control Module is 9 V or higher. | A |
| BATT Voltage for Gear Shift Control Module is below 9 V. | B |
Turn the ignition switch off.
A
B
Enter the following menus:
| Tester Display |
|---|
| Diagnosis Related Information |
Check for diagnosis related information.
| Result | Proceed to |
|---|---|
| No diagnosis related information is output. | A |
| The diagnosis related information in the table below is output. | B |
| Diagnosis Related Information |
|---|
| P085011 |
| P085015 |
Turn the ignition switch off.
A
B
| *1 | Luggage Room Relay Block |
| *2 | P CON MTR Relay |
Remove the P CON MTR relay from the luggage room relay block.
| *1 | P CON MTR Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
Install the P CON MTR relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the P position switch (parking switch) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D93 shift control ECU connector.
Disconnect the D17 P position switch (parking switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93,D17)Location & Routingewd_type=routing;type=c,c;code=D93,D17 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=10 Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switchewd_type=component;type=c;code=D17;pinno=2 |
||
| D93-10 (P1) - D17-2 (S) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93,D17)Location & Routingewd_type=routing;type=c,c;code=D93,D17 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=10 Click Connector(D17)Instrument Panel>Instrument Panel Wire>Parking Switchewd_type=component;type=c;code=D17;pinno=2 |
||
| D93-10 (P1) or D17-2 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the D17 P position switch (parking switch) connector.
Reconnect the D93 shift control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D93 shift control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93)Location & Routingewd_type=routing;type=c;code=D93 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=1 |
||
| D93-1 (BATT) - Body ground | Ignition switch off | 8 to 15.4 V |
Reconnect the D93 shift control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the shift control ECU connector.
Remove the P CON MAIN fuse from the luggage room relay block.
| *1 | Luggage Room Relay Block | *2 | P CON MAIN Fuse |
| *a | Front view of wire harness connector
(to Shift Control ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93)Location & Routingewd_type=routing;type=c;code=D93 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=1 |
||
| P CON MAIN fuse terminal 2 - D93-1 (BATT) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D93)Location & Routingewd_type=routing;type=c;code=D93 Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECUewd_type=component;type=c;code=D93;pinno=1 |
||
| P CON MAIN fuse terminal 2 or D93-1 (BATT) - Body ground | Always | 10 kΩ or higher |
Reconnect the shift control ECU connector.
Install the P CON MAIN fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Luggage Room Relay Block |
| *2 | P CON MAIN Fuse |
Remove the P CON MAIN fuse from the luggage room relay block.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the cable from the positive (+) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P CON MAIN fuse terminal 1 - Auxiliary battery positive (+) cable | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P CON MAIN fuse terminal 1 - Body ground | Always | 10 kΩ or higher |
Connect the cable to the positive (+) auxiliary battery terminal.
Connect the cable to the negative (-) auxiliary battery terminal.
Install the P CON MAIN fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Charge the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Depress the brake pedal and move the shift lever to select neutral (N).
Push the P position switch (parking switch) to select park (P).
Check that if there is an error message displayed on the multi-information display.
| Result | Proceed to |
|---|---|
| "Shift system unavailable Apply electric parking brake securely when parking See owner's manual" is not displayed on the multi-information display. | A |
| "Shift system unavailable Apply electric parking brake securely when parking See owner's manual" is displayed on the multi-information display. | B |
Turn the ignition switch off.
A
B