Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver communicate by direct line. If a malfunction occurs in this communication signal, B1247 is output by the main body ECU (multiplex network body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B1247 Tire Pressure Monitor Receiver Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is lost for 10 seconds or more.
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)


Main Body A

WIRING DIAGRAM

excluding JPD20R-CEDSSW (w/ Panic Switch):
C385228E45
1.292,1.115 1.75,1.313 0.458,0.198 10 false CPU 0.177,1.719 0.635,2.063 0.458,0.344 10 false G49 0.177,1.917 3.104,2.135 2.927,0.219 10 false Tire Pressure Warning ECU and Receiver 4.271,1.75 4.604,1.958 0.333,0.208 10 false D14 4.281,1.958 6.229,2.313 1.948,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.698,1.031 5.156,1.229 0.458,0.198 10 false RDA 2.135,0.865 2.479,1.063 0.344,0.198 10 false RDA 4.375,0.896 4.833,1.094 0.458,0.198 10 false 10 2.625,0.917 3.083,1.115 0.458,0.198 10 false 4

for JPD20R-CEDSSW (w/ Panic Switch):
C385228E47
1.292,1.115 1.75,1.313 0.458,0.198 10 false CPU 0.177,1.719 0.635,2.063 0.458,0.344 10 false G96 0.177,1.917 3.104,2.135 2.927,0.219 10 false Tire Pressure Warning ECU and Receiver 4.271,1.75 4.604,1.958 0.333,0.208 10 false D14 4.281,1.958 6.229,2.313 1.948,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.698,1.031 5.156,1.229 0.458,0.198 10 false RDA 2.042,0.865 2.458,1.063 0.417,0.198 10 false RDA2 4.375,0.896 4.833,1.094 0.458,0.198 10 false 10 2.625,0.917 3.083,1.115 0.458,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
excluding JPD20R-CEDSSW (w/ Panic Switch) A
for JPD20R-CEDSSW (w/ Panic Switch) B



A

2.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)

B

5.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)
2.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)
a.
C385229C68
1.24,0.24 1.677,0.5 0.438,0.26 1.042,1.792 1.365,1.146 true 0.292,0.271 0.604,0.469 0.313,0.198 10 false *a 2.875,3.396 3.188,3.594 0.313,0.198 10 false *b 1.344,0.313 1.656,0.51 0.313,0.198 10 false G49 0.927,1.823 1.313,2.01 0.385,0.188 10 false RDA
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-4 (RDA) - Body ground 5 V/DIV. 5 ms./DIV. Ignition switch ON Waveform generation


Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 10.5 V or higher and 0.5 V or less) A
Waveform does not change from 10. 5 V or higher B
Waveform does not change from 0.5 V or less C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

C

3.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
3.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)

Pre-procedure1

a.

Disconnect the G49 tire pressure warning ECU and receiver connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-4 (RDA) - Body ground Ignition switch ON 10.5 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

NG

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G49 tire pressure warning ECU and receiver connector.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,G49)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

D14-10 (RDA) - G49-4 (RDA) Always Below 1 Ω
D14-10 (RDA) or G49-4 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (OUTPUT WAVEFORM)
a.
C385229C70
1.24,0.24 1.677,0.5 0.438,0.26 1.042,1.792 1.365,1.146 true 0.292,0.271 0.604,0.469 0.313,0.198 10 false *a 2.875,3.396 3.188,3.594 0.313,0.198 10 false *b 1.323,0.302 1.635,0.5 0.313,0.198 10 false G96 0.875,1.833 1.51,2.021 0.635,0.188 10 false RDA2
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition

Click Location & Routing(G96)Location & Routing

Click Connector(G96)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning Receiver Assembly

G96-4 (RDA2) - Body ground 5 V/DIV. 5 ms./DIV. Ignition switch ON Waveform generation


Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 10.5 V or higher and 0.5 V or less) A
Waveform does not change from 10. 5 V or higher B
Waveform does not change from 0.5 V or less C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

C

6.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
6.CHECK TERMINAL VOLTAGE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OUTPUT)
a.

Disconnect the G96 tire pressure warning ECU and receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G96)Location & Routing

Click Connector(G96)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning Receiver Assembly

G96-4 (RDA2) - Body ground Ignition switch ON 10.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G96 tire pressure warning ECU and receiver connector.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,G96)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(G96)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning Receiver Assembly

D14-10 (RDA) - G96-4 (RDA2) Always Below 1 Ω
D14-10 (RDA) or G96-4 (RDA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR