Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C2179 Tire Pressure Monitor ECU Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Wire harness or connector

·

Tire pressure warning ECU and receiver

·

Main body ECU (Multiplex network body ECU)


Tire Pressure Monitor B

WIRING DIAGRAM

excluding JPD20R-CEDSSW (w/ Panic Switch):
C385230E32
1.292,2.948 1.75,3.146 0.458,0.198 10 false CPU 2.188,2.719 2.646,2.917 0.458,0.198 10 false PRG 4.698,2.854 5.75,3.031 1.052,0.177 10 false PRG 4.677,1.302 5.135,1.5 0.458,0.198 10 false +B 4.688,0.563 5.146,0.76 0.458,0.198 10 false IG 3.396,1.458 4.531,1.646 1.135,0.188 10 false ECU-B P NO.4 3.323,0.719 4.521,0.906 1.198,0.188 10 false LUG-IG1 NO.2 1.552,1.26 3.052,1.49 1.5,0.229 10 false from Auxiliary Battery 1.948,0.542 2.99,0.76 1.042,0.219 10 false from IG Circuit 4.365,1.156 4.823,1.354 0.458,0.198 10 false 7 4.427,0.417 4.885,0.615 0.458,0.198 10 false 1 4.406,2.708 4.865,2.906 0.458,0.198 10 false 5 2.604,2.708 3.063,2.906 0.458,0.198 10 false 11 0.333,3.469 0.792,3.667 0.458,0.198 10 false D14 3.917,3.406 4.25,3.646 0.333,0.24 10 false G49 3.885,3.656 6.625,3.958 2.74,0.302 10 false Tire Pressure Warning ECU and Receiver 0.344,3.667 3.396,3.969 3.052,0.302 10 false Main body ECU (Multiplex network body ECU)

for JPD20R-CEDSSW (w/ Panic Switch):
C452726E01
1.292,2.948 1.75,3.146 0.458,0.198 10 false CPU 2.188,2.719 2.646,2.917 0.458,0.198 10 false PRG 4.698,2.854 5.75,3.031 1.052,0.177 10 false PRG2 4.688,0.563 5.146,0.76 0.458,0.198 10 false IG 3.323,0.719 4.521,0.906 1.198,0.188 10 false LUG-IG1 NO.2 1.948,0.542 2.99,0.76 1.042,0.219 10 false from IG Circuit 4.427,0.417 4.885,0.615 0.458,0.198 10 false 1 4.406,2.708 4.865,2.906 0.458,0.198 10 false 5 2.604,2.708 3.063,2.906 0.458,0.198 10 false 11 0.333,3.469 0.792,3.667 0.458,0.198 10 false D14 3.896,3.406 4.229,3.646 0.333,0.24 10 false G96 3.885,3.677 6.625,3.979 2.74,0.302 10 false Tire Pressure Warning ECU and Receiver 0.344,3.667 3.396,3.969 3.052,0.302 10 false Main body ECU (Multiplex network body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
excluding JPD20R-CEDSSW (w/ Panic Switch) A
for JPD20R-CEDSSW (w/ Panic Switch) B



A

2.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)

B

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)
2.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)
a.
C385231C34
1.219,0.219 1.615,0.448 0.396,0.229 0.865,1.729 1.156,1.094 true 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 2.875,3.406 3.188,3.604 0.313,0.198 10 false *b 0.719,1.771 1.125,2 0.406,0.229 10 false PRG 1.302,0.271 1.708,0.5 0.406,0.229 10 false D14
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-11 (PRG) - Body ground 5 V/DIV.5 ms./DIV. Ignition switch ON Waveform generation


Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 9.8 V or higher and 1.2 V or less) A
Waveform does not change from 9.8 V or higher B
Waveform does not change from 1.2 V or less C




A

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

3.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
3.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)

Pre-procedure1

a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-11 (PRG) - Body ground Ignition switch ON 9.8 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
4.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G49 tire pressure warning ECU and receiver connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G49,D14)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

G49-5 (PRG) - D14-11 (PRG) Always Below 1 Ω
G49-5 (PRG) or D14-11 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G49)Location & Routing

Click Connector(G49)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning ECU and Receiver (Electrical Key & Tire Pressure Monitoring System Receiver Assembly)

G49-7 (+B) - Body ground Always 10 to 16 V
G49-1 (IG) - Body ground Ignition switch ON 10 to 16 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)
a.
C385231C34
1.219,0.219 1.615,0.448 0.396,0.229 0.865,1.729 1.156,1.094 true 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 2.875,3.406 3.188,3.604 0.313,0.198 10 false *b 0.719,1.771 1.125,2 0.406,0.229 10 false PRG 1.302,0.271 1.708,0.5 0.406,0.229 10 false D14
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-11 (PRG) - Body ground 5 V/DIV.5 ms./DIV. Ignition switch ON Waveform generation


Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 9.8 V or higher and 1.2 V or less) A
Waveform does not change from 9.8 V or higher B
Waveform does not change from 1.2 V or less C




A

B

4.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

7.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
7.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)

Pre-procedure1

a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-11 (PRG) - Body ground Ignition switch ON 9.8 V or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

8.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
8.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the G96 tire pressure warning ECU and receiver connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G96,D14)Location & Routing

Click Connector(G96)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning Receiver Assembly

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

G96-5 (PRG) - D14-11 (PRG) Always Below 1 Ω
G96-5 (PRG) or D14-11 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

9.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G96)Location & Routing

Click Connector(G96)Body>Floor Wire / No. 3 Floor Wire>Tire Pressure Warning Receiver Assembly

G96-1 (IG) - Body ground Ignition switch ON 10 to 16 V


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR