Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM37H0E _55 Steering _097126 POWER ASSIST SYSTEMS _0454879 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C123A17  Supply Voltage Circuit Circuit Voltage Above Threshold  C15E0A2  Power Steering Control Module Processor (System 1) System Voltage Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
C123A17 Supply Voltage Circuit Circuit Voltage Above Threshold IG voltage of system 1 is at or higher than the specified value
·

Harness or connector

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on EMPS A
C15E0A2 Power Steering Control Module Processor (System 1) System Voltage Low
·

System 1 does not start due to an internal malfunction in the system 1

·

IG voltage of system 1 is at or lower than the specified value


·

Harness or connector

·

Rack and pinion power steering gear assembly


EPS warning light: Comes on EMPS A

DTC Detection Conditions: C15E0A2
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status System 1 does not start due to an internal malfunction in the system 1 ○ -
IG voltage of system 1 is at or lower than the specified value - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

for LHD:
C441858E07
3.917,2.667 7.083,2.948 3.167,0.281 10 false Rack and Pinion Power Steering Gear Assembly 1.771,0.552 2.385,0.771 0.615,0.219 10 false EPS-IG1 5.656,0.385 5.885,0.573 0.229,0.188 10 false IG 5.667,0.885 6.146,1.063 0.479,0.177 10 false PGND 4.833,0.271 5.375,0.531 0.542,0.26 10 false 9 4.844,0.729 5.385,0.99 0.542,0.26 10 false 7 3.917,2.385 4.146,2.573 0.229,0.188 10 false a1 5.24,1.292 6.531,1.531 1.292,0.24 10 false Power Steering ECU

for RHD:
C441858E08
3.917,2.667 7.083,2.948 3.167,0.281 10 false Rack and Pinion Power Steering Gear Assembly 1.771,0.552 2.385,0.771 0.615,0.219 10 false EPS-IG1 5.656,0.385 5.885,0.573 0.229,0.188 10 false IG 5.667,0.885 6.146,1.063 0.479,0.177 10 false PGND 4.833,0.271 5.375,0.531 0.542,0.26 10 false 4 4.844,0.729 5.385,0.99 0.542,0.26 10 false 7 3.917,2.385 4.365,2.573 0.448,0.188 10 false A79 5.24,1.292 6.531,1.531 1.292,0.24 10 false Power Steering ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the rack and pinion power steering gear assembly, perform Power Steering ECU Initial Setting.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>UTILITY



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK HARNESS AND CONNECTOR (PGND)

B

6.CHECK HARNESS AND CONNECTOR (PGND)
2.CHECK HARNESS AND CONNECTOR (PGND)

Pre-procedure1

a.

Disconnect the a1 rack and pinion power steering gear assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(a1)Location & Routing

Click Connector(a1)Engine Compartment>ECU Wire Sub-Assembly>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)

a1-7 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (IG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG)

Pre-procedure1

a.

Disconnect the a1 rack and pinion power steering gear assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(a1)Location & Routing

Click Connector(a1)Engine Compartment>ECU Wire Sub-Assembly>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)

a1-9 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > EMPS > Clear DTCs
50002 405

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 405

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (PGND)

Pre-procedure1

a.

Disconnect the A79 rack and pinion power steering gear assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A79)Location & Routing

Click Connector(A79)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)

A79-7 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (IG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IG)

Pre-procedure1

a.

Disconnect the A79 rack and pinion power steering gear assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A79)Location & Routing

Click Connector(A79)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)

A79-4 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR