Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1413  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed to the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator, which is used to control the air conditioning system. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1413 Evaporator Temperature Sensor Circuit
·

Diagnosis condition: None

·

Malfunction status: Open or short in evaporator temperature sensor circuit

·

Detection time: None (Present malfunction), continuously for 4 seconds or more (Past malfunction)


·

No. 1 cooler thermistor

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

WIRING DIAGRAM

E316646E55
4.958,1.625 5.271,1.823 0.313,0.198 10 false z1 4.969,1.76 6.542,2.135 1.573,0.375 10 false Air Conditioning Amplifier Assembly 6.167,0.635 6.479,0.833 0.313,0.198 10 false AD 5.719,0.219 6.031,0.417 0.313,0.198 10 false 5 V 4.792,0.521 5.104,0.719 0.313,0.198 10 false TEA 4.813,1 5.281,1.198 0.469,0.198 10 false SGA 4.51,0.521 4.823,0.719 0.313,0.198 10 false 6 4.51,0.99 4.979,1.188 0.469,0.198 10 false 5 3.083,1.385 4.615,1.771 1.531,0.385 10 false Air Conditioning Harness Assembly 3,0.521 3.313,0.719 0.313,0.198 10 false 2 3.01,1 3.323,1.198 0.313,0.198 10 false 1 1.135,1.521 2.75,1.76 1.615,0.24 10 false No. 1 Cooler Thermistor

PROCEDURE

1.READ VALUE USING GTS (EVAPORATOR FIN THERMISTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed No. 1 cooler thermistor system malfunction
·

When open circuit: -29.70°C (-21.46°F)

·

When short circuit: 59.55°C (139.19°F)


Body Electrical > Air Conditioner > Data List
Tester Display
Evaporator Fin Thermistor
50003 121 3
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.INSPECT NO. 1 COOLER THERMISTOR
2.INSPECT NO. 1 COOLER THERMISTOR

OK

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

NG

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

Pre-procedure1

a.

Remove the air conditioning harness assembly.

HINT:

for LHD:Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for LHD)>DISASSEMBLY

for RHD:Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for RHD)>DISASSEMBLY


E378688C42
0.917,0.833 1.333,1.083 0.417,0.25 1.333,1.583 1.667,1.583 1.667,1.583 1.781,1.26 true 2.323,1.583 1.99,1.583 1.99,1.583 1.927,1.25 true 1.167,0.229 1.479,0.427 0.313,0.198 10 false *a 4.469,0.302 4.781,0.5 0.313,0.198 10 false *b 1.073,0.896 1.385,1.094 0.313,0.198 10 false z1 0.99,1.5 1.479,1.719 0.49,0.219 10 false SGA 2.396,1.479 2.885,1.698 0.49,0.219 10 false TEA
*a Front view of air conditioning harness assembly connector
(to Air Conditioning Amplifier Assembly)
*b Front view of air conditioning harness assembly connector
(to No. 1 Cooler Thermistor)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z1)Location & Routing

Click Connector(z1)Instrument Panel>other>Air Conditioning Harness Assembly , Air Conditioning Amplifier Assembly

z1-6 (TEA) - 2 Always Below 1 Ω
z1-5 (SGA) - 1 Always Below 1 Ω
z1-6 (TEA) or 2 - Other terminals and body ground Always 10 kΩ or higher
z1-5 (SGA) or 1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG