Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet mode selection No. 1 blower damper servo sub-assembly to the appropriate position, which controls the air inlet mode (fresh, recirculation/fresh, and recirculation).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1442 Air Inlet Damper Control Servo Motor Circuit
Diagnosis condition:

During No. 1 blower damper servo sub-assembly operation


Malfunction status:

The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning


Detection time:

Continuously for 30 seconds or more


·

No. 1 blower damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized Air Conditioner B

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition During No. 1 blower damper servo sub-assembly operation ○ ○
Malfunction Status The damper servo operation request signal is output but the position information of the servo does not change ○ -
The damper servo operation request signal is output but the position information of the servo is malfunctioning - ○
Detection Time Continuously for 30 seconds or more Continuously for 30 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


WIRING DIAGRAM

E459549E16
5.021,1.969 6.615,2.323 1.594,0.354 10 false Air Conditioning Amplifier Assembly 5.844,0.594 6.417,0.802 0.573,0.208 10 false IC 6.427,0.76 7,0.969 0.573,0.208 10 false +B 4.844,1.094 5.396,1.271 0.552,0.177 10 false BUS G 4.594,1.104 5.156,1.281 0.563,0.177 10 false 2 4.833,0.792 5.385,0.969 0.552,0.177 10 false B BUS 4.604,0.792 5.156,0.969 0.552,0.177 10 false 4 4.823,0.479 5.375,0.656 0.552,0.177 10 false BUS 4.594,0.417 5.146,0.594 0.552,0.177 10 false 3 5.031,1.802 5.479,1.979 0.448,0.177 10 false z1 0.365,1.719 3.01,2.01 2.646,0.292 10 false No. 1 Blower Damper Servo Sub-assembly 3.24,1.74 4.802,2.104 1.563,0.365 10 false Air Conditioning Harness Assembly 0.729,2.406 3.156,2.604 2.427,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

·

When installing the damper servo motor, make sure to install it correctly.

·

When the servo motor is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION



HINT:

Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
B1442 is output A
B1442 and B1497 are output B



A

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

B

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
a.

Check for No. 1 blower damper servo sub-assembly is installed correctly.

OK:

No. 1 blower damper servo sub-assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)

NG

REINSTALL NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

3.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)
a.

Check for a wire harness caught between the links of the motors and dampers.

OK:

No wire harnesses are caught between the links of the motors and dampers.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOWER ASSEMBLY (DAMPER)

NG

REMOVE PINCHED NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

4.CHECK BLOWER ASSEMBLY (DAMPER)

Pre-procedure1

a.

Remove the No. 1 blower damper servo sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY



Procedure1

a.

Operate the dampers by hand.

OK:

The dampers are easily operated by hand.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE BLOWER ASSEMBLY