Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0455143 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Odo/Trip Switch Malfunction  


DESCRIPTION

The ODO/TRIP display of the combination meter changes each time the trip switch is pressed.

WIRING DIAGRAM

E367032E12
4.438,3.135 6.302,3.354 1.865,0.219 10 false Combination Meter Assembly 4.448,2.969 4.906,3.167 0.458,0.198 10 false D41 5.615,1.531 6.073,1.729 0.458,0.198 10 false I/F 2.635,0.833 3.094,1.031 0.458,0.198 10 false A/B 2.76,2.021 2.958,2.219 0.198,0.198 10 false E 3.042,0.844 3.198,1.042 0.156,0.198 10 false 9 4.448,0.844 4.604,1.042 0.156,0.198 10 false 4 3.042,2.021 3.198,2.219 0.156,0.198 10 false 1 4.385,2.042 4.698,2.24 0.313,0.198 10 false 26 4.688,0.844 5.146,1.042 0.458,0.198 10 false ODO 4.688,2.042 5.146,2.24 0.458,0.198 10 false SW3 1.865,2.521 2.323,2.719 0.458,0.198 10 false D7 1.885,2.698 2.625,2.948 0.74,0.25 10 false Trip Switch 1.906,1.156 2.625,1.344 0.719,0.188 10 false ODO TRIP

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (ODO/TRIP CHANGE SW)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ODO/TRIP Change Switch ODO/TRIP switch (Trip switch) OFF/ON OFF: Switch released
ON: Switch pushed
-
Body Electrical > Combination Meter > Data List
Tester Display
ODO/TRIP Change Switch
50003 409 2
OK:

ODO/TRIP switch condition displayed on the GTS changes with the actual switch operation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT TRIP SWITCH
2.INSPECT TRIP SWITCH

OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TRIP SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TRIP SWITCH)
a.

Disconnect the D41 combination meter assembly connector.


b.

Disconnect the D7 trip switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41,D7)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

Click Connector(D7)Instrument Panel>Instrument Panel Wire>Trip Switch

D41-4 (ODO) - D7-9 (A/B) Always Below 1 Ω
D41-26 (SW3) - D7-1 (E) Always Below 1 Ω
D41-4 (ODO) or D7-9 (A/B) - Body ground Always 10 kΩ or higher
D41-26 (SW3) or D7-1 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR