Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2020.11–2021.08
RM37H0E _58 Vehicle Interior _095297 SEAT BELT _0455415 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the state of the front seat inner belt assembly (for Driver Side).

WIRING DIAGRAM

E414182E26
2.604,0.865 3.333,1.125 0.729,0.26 10 false 22*1, 4*2 4.271,1 4.667,1.385 0.396,0.385 10 false DBKL 5.906,2.146 7.104,2.646 1.198,0.5 10 false Combination Meter Assembly 0.813,3.344 2.531,3.552 1.719,0.208 10 false : CAN Communication Line 3.99,0.844 4.188,1.073 0.198,0.229 10 false 18 1.865,0.854 2.063,1.125 0.198,0.271 10 false 3 0.583,0.875 0.823,1.219 0.24,0.344 10 false 2 3.813,2.302 5.458,2.677 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.208,1.417 1.281,1.76 1.073,0.344 10 false G24*1, G22*2 0.208,1.583 2.146,2.063 1.938,0.479 10 false Front Seat Inner Belt Assembly (for Driver Side) 2.51,1.573 4.135,2.115 1.625,0.542 10 false Driver Side Panel Junction Block Assembly 0.375,2.927 3.563,3.271 3.188,0.344 10 false *2: for RHD 0.385,2.573 3.573,2.917 3.188,0.344 10 false *1: for LHD 3.833,2.115 4.104,2.354 0.271,0.24 10 false A 1.615,0.906 1.771,1.104 0.156,0.198 10 false + 0.802,0.906 0.958,1.104 0.156,0.198 10 false E 2.5,1.396 3.229,1.594 0.729,0.198 10 false 4H

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REASSEMBLY


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch OFF or ON OFF: Driver seat belt unfastened
ON: Driver seat belt fastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)

OK

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the G24*1 or G22*2 front seat inner belt assembly (for Driver Side) connector.


b.

Disconnect the 4H driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(G24)Location & Routing

Click Connector(G24)Seat>Floor Wire>Front Seat Inner Belt Assembly LH

4H-22 - G24-3 (+) Always Below 1 Ω
4H-22 or G24-3 (+) - Body ground Always 10 kΩ or higher
G24-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(G22)Location & Routing

Click Connector(G22)Seat>Floor Wire>Front Seat Inner Belt Assembly RH

4H-4 - G22-3 (+) Always Below 1 Ω
4H-4 or G22-3 (+) - Body ground Always 10 kΩ or higher
G22-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B491251C14
1.948,0.719 2.365,0.958 0.417,0.24 5.552,0.625 5.948,0.865 0.396,0.24 2.427,1.979 2.427,1.552 false 5.667,0.656 5.979,0.854 0.313,0.198 10 false 4H 2.115,0.76 2.427,0.958 0.313,0.198 10 false A 0.344,0.167 0.656,0.365 0.313,0.198 10 false *a 2.25,2 2.865,2.198 0.615,0.198 10 false DBKL
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A-18 (DBKL) - 4H-22 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A-18 (DBKL) - 4H-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY