Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and to perform repairs.




DIAGNOSIS FUNCTION


a.

The blind spot monitor system displays an error message on the multi-information display to inform the driver that the system is unavailable either temporarily or due to a malfunction.

·

When the system is unavailable temporarily:

Multi-information display displays "BSM Unavailable See Owner's Manual".

·

When the system is unavailable due to a malfunction:

Multi-information display displays "Blind Spot Monitor Malfunction Visit Your Dealer".



b.

The RCTA function displays an error message on the multi-information display to inform the driver that the system is unavailable either temporarily or due to a malfunction.

·

When the system is unavailable temporarily:

Multi-information display displays "RCTA Unavailable".

·

When the system is unavailable due to a malfunction:

Multi-information display displays "RCTA Malfunction Visit Your Dealer".



c.

The automatic rear flashing hazard lights function displays an error message on the multi-information display to inform the driver that the system is unavailable either temporarily or due to a malfunction.

·

When the system is unavailable temporarily:

Multi-information display displays "FHL Not Available".

·

When the system is unavailable due to a malfunction:

Multi-information display displays "FHL Malfunction Visit Your Dealer".




ABNORMALITY HISTORY


HINT:

The abnormality history for a blind spot monitor sensor can be displayed or cleared.


a.

Check abnormality history

i.

Turn the blind spot monitor system on.


ii.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Abnormal History
50005 313 4241
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Abnormal History
50005 314 4242

iii.

Check the results displayed for the abnormality history check.

HINT:
·

If "Yes" is displayed, check the suspected area column for each item.

·

Abnormality history is stored only for the blind spot monitor sensor for which an abnormality has been detected.

·


Abnormality History Table
Tester Display Item Explanation Suspected Area
History of Module Blockage History of blind spot monitor sensor detection problems due to snow, rain, etc. on the bumper
·

Check if a bumper that is not compatible with the blind spot monitor sensors (such as a non-genuine part) is installed

·

Check if any foreign matter is attached to the bumper

·

Check if any foreign matter is present between the bumper and sensors


History of Low Voltage History of low supply auxiliary battery voltage from auxiliary battery to the blind spot monitor sensor Power Source Circuit
Click here(Click here)
History of High Voltage History of high supply auxiliary battery voltage from auxiliary battery to the blind spot monitor sensor
History of Low Temperature History of low temperature for the blind spot monitor sensor
·

Check the outside temperature

·

Check if any foreign matter is attached to the blind spot monitor sensors and their surrounding areas


History of High Temperature History of high temperature for the blind spot monitor sensor



b.

Clear abnormality history

i.

Turn the blind spot monitor system on.


ii.

Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master Abnormal History or BSM Slave Abnormal History.

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Abnormal History
50005 313 4241
Body Electrical > Blind Spot Monitor Slave > Utility
Tester Display
BSM Slave Abnormal History
50005 314 4242

iii.

Clear the abnormality history.