Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455114 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The blind spot monitor sensor receives steering angle signals from the steering sensor via CAN communication.

Blind Spot Monitor Master
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1A47 Steering Angle Sensor A fail flag is transmitted from the steering sensor
·

Steering sensor

·

Blind spot monitor sensor RH


Blind Spot Monitor Master A

Blind Spot Monitor Slave
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1A47 Steering Angle Sensor A fail flag is transmitted from the steering sensor
·

Steering sensor

·

Blind spot monitor sensor LH


Blind Spot Monitor Slave A

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Result Proceed to
C1A47 is not output A
C1A47 is output B



A

4.CHECK FOR DTC

B

5.REPLACE STEERING SENSOR
4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
C1A47 is not output A
C1A47 is output B



A

B

5.REPLACE STEERING SENSOR
5.REPLACE STEERING SENSOR
a.

Replace the steering sensor with a new or known good one.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313

Result:
Result Proceed to
C1A47 is not output A
C1A47 is output B



A

9.CHECK FOR DTC

B

9.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Result Proceed to
C1A47 is not output A
C1A47 is output B



A

END (STEERING SENSOR WAS DEFECTIVE)

B