Home › Power Source / Network › POWER DISTRIBUTION › POWER INTEGRATION SYSTEM
RM37H0E _57 Power Source / Network _095301 POWER DISTRIBUTION _0455449 POWER INTEGRATION SYSTEM U

POWER DISTRIBUTION  POWER INTEGRATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C07
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.625 1.573,0.26 1.573,0.26 1.781,0.26 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.219 2.146,0.417 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the main body ECU (multiplex network body ECU) connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground Ground Always Below 1 Ω
A-31 (BECU) - Body ground Battery power supply Always 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D14-5 (CXP1) - Body ground CXPI communication line Ignition switch ON Pulse generation



CHECK NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU (w/ PTC Heater)


E360199C23
2.51,0.125 2.917,0.365 0.406,0.24 3.823,0.125 4.229,0.365 0.406,0.24 2.573,0.156 2.958,0.448 0.385,0.292 10 false A59 3.865,0.156 4.458,0.49 0.594,0.333 10 false D123 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a
*a Component without harness connected
(No. 1 Semiconductor Power Integration ECU)
- -


a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A59-1 (+B) - Body ground Battery power supply Ignition switch off 8 to 14 V
D123-1 (L) - Body ground No. 1 headlight ECU sub-assembly LH power supply Ignition switch off Below 3 V
Ignition switch ON 8 V or higher
D123-2 (L) - Body ground No. 1 headlight ECU sub-assembly RH power supply Ignition switch off Below 3 V
Ignition switch ON 8 V or higher
D123-9 (IG) - Body ground Ignition power supply Ignition switch off Below 1.5 V
Ignition switch ON 8 to 14 V
D123-13 (GND) - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D123-7 (CXPI) - Body ground CXPI communication line Ignition switch ON Pulse generation



CHECK NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU


E360199C22
2.51,0.125 2.917,0.365 0.406,0.24 3.823,0.125 4.229,0.365 0.406,0.24 2.604,0.156 3.021,0.396 0.417,0.24 10 false J5 3.854,0.177 4.219,0.448 0.365,0.271 10 false G102 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a
*a Component without harness connected
(No. 2 Semiconductor Power Integration ECU)
- -


a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
J5-1 (+B) - Body ground Battery power supply Ignition switch off 8 to 14 V
G102-1 (OUT) - Body ground Stop lights, high mounted stop light output Brake pedal released Below 3 V
Brake pedal depressed 8 V or higher
G102-2 (L) - Body ground Window defogger output Ignition switch ON, window defogger switch off Below 3 V
Ignition switch ON, window defogger switch on 8 V or higher
G102-4 (L) - Body ground Back-up output Engine running, shift lever in any position other than R Below 3 V
Engine running, shift lever in R 8 V or higher
G102-6 (GND2) - Body ground Ground Always Below 1 Ω
G102-9 (IG) - Body ground Ignition power supply Ignition switch off Below 1.5 V
Ignition switch ON 8 to 14 V
G102-10 (STP) - Body ground Stop lights operation signal input Brake pedal released Below 1.5 V
Brake pedal depressed 6 V or higher
G102-11 (+S) - Body ground Back-up light operation signal input Engine running, shift lever in any position other than R Below 1.5 V
Engine running, shift lever in R 6 V or higher
G102-13 (GND1) - Body ground Ground Always Below 1 Ω
G102-14 (ACC) - Body ground ACC stop lights operation signal input Ignition switch off 6 V or higher
Ignition switch ON Below 1.5 V
G102-16 (L) - Body ground Rear taillights output Rear taillights not illuminated Below 3 V
Rear taillights illuminated 8 V or higher


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
G102-7 (CXPI) - Body ground CXPI communication line Ignition switch ON Pulse generation