CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Remove the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A-11 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| A-30 (ACC) - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | ||
| A-31 (BECU) - Body ground | Battery power supply | Always | 11 to 14 V |
| A-32 (IG) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the pulse according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A-16 (LIN2) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH (w/ Reverse Shift-linked Mirror)
Disconnect the E25 front multiplex network door ECU LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E25-3 (SIG) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| E25-4 (CPUB) - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
| E25-6 (BDR) - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
| E25-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E25 front multiplex network door ECU LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E25-5 (BDRJ) - Body ground | Power window regulator motor power supply | Ignition switch off | 11 to 14 V |
| E25-2 (PWE) - Body ground | Power window regulator motor power supply | Always | Below 1 Ω |
| E25-9 (SGND) - Body ground | Power window regulator motor power supply | Always | Below 1 Ω |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E25-11 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| E25-12 (LIN2) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| E25-13 (LIN3) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH (w/ Reverse Shift-linked Mirror)
Disconnect the E7 front multiplex network door ECU RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E7-3 (SIG) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| E7-4 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch ON | 11 to 14 V |
| E7-6 (BDR) - Body ground | Auxiliary battery power supply | Ignition switch ON | 11 to 14 V |
| E7-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E7 front multiplex network door ECU RH connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E7-5 (BDRJ) - Body ground | Power window regulator motor power supply | Ignition switch ON | 11 to 14 V |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E7-11 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| E7-13 (LIN3) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR MULTIPLEX NETWORK DOOR ECU LH (w/ Double Locking System)
Disconnect the F16 rear multiplex network door ECU LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F16-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| F16-4 (BDR) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| F16-11 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| F16-12 (SIG) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F16-22 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| F16-23 (LIN3) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR MULTIPLEX NETWORK DOOR ECU RH (w/ Double Locking System)
Disconnect the F5 rear multiplex network door ECU RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F5-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| F5-4 (BDR) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| F5-11 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch ON | 11 to 14 V |
| F5-12 (SIG) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch off | 11 to 14 V |
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F5-22 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
| F5-23 (LIN3) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
Disconnect the E32 multiplex network master switch assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E32-11 (B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| E32-12 (GND) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E32 multiplex network master switch assembly connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E32-17 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Disconnect the E20 front power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E20-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| E20-2 (B) - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
Reconnect the E20 front power window regulator motor assembly LH connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E20-9 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
Disconnect the E2 front power window regulator motor assembly RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E2-1 (GND) - Body ground | Ground | Ignition switch off | Below 1 Ω |
| E2-2 (B) - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
Reconnect the E2 front power window regulator motor assembly RH connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| E2-9 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Disconnect the F12 rear power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F12-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| F12-2 (B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the F12 rear power window regulator motor assembly LH connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F12-9 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
Disconnect the F1 rear power window regulator motor assembly RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F1-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| F1-2 (B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the F1 rear power window regulator motor assembly RH connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| F1-9 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the D86 certification ECU (smart key ECU assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D86-4 (+B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| D86-18 (E) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D86 certification ECU (smart key ECU assembly) connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D86-13 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY
Disconnect the D24 steering lock actuator or upper bracket assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D24-1 (GND) - Body ground | Ground | Always | Below 1 Ω |
| D24-6 (IG2) - Body ground | IG power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | ||
| D24-7 (B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the D24 steering lock actuator or upper bracket assembly connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D24-5 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK ID CODE BOX (IMMOBILISER CODE ECU)
Disconnect the D73 ID code box (immobiliser code ECU) connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D73-1 (+B) - Body ground | Auxiliary battery power supply | Always | 11 to 14 V |
| D73-5 (GND) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D73 ID code box (immobiliser code ECU) connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| D73-2 (LIN1) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |
CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (w/ Roof Sunshade System)
Disconnect the H4 sliding roof drive gear sub-assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H4-1 (B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| H4-2 (E) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H4 sliding roof drive gear sub-assembly connector.
Measure the pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H4-7 (LIN) - Body ground | LIN communication line | Ignition switch ON | Pulse generation |