Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455450 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator or upper bracket assembly stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2786 No Response from Steering Lock ECU Communication between the certification ECU (smart key ECU assembly) and steering lock actuator or upper bracket assembly stops for 10 seconds or more.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator or upper bracket assembly

·

Harness or connector


Entry&Start B

WIRING DIAGRAM

B498108E11
0.646,1.375 3.563,1.667 2.917,0.292 10 false Certification ECU (Smart Key ECU Assembly) 0.667,1.188 1.177,1.458 0.51,0.271 10 false D86 1.927,0.927 2.385,1.125 0.458,0.198 10 false LIN 2.281,0.771 2.594,0.969 0.313,0.198 10 false 13 5.26,0.76 5.573,0.958 0.313,0.198 10 false 5 2.167,1.719 3.604,2.01 1.438,0.292 10 false from Auxiliary Battery 2.406,2.365 3.823,2.656 1.417,0.292 10 false from IG2 D Relay 3.979,1.583 4.802,1.76 0.823,0.177 10 false STRG LOCK 4.042,2.229 5.135,2.448 1.094,0.219 10 false IG2 D NO.2 5.26,1.625 5.417,1.823 0.156,0.198 10 false 7 5.26,2.292 5.417,2.49 0.156,0.198 10 false 6 5.281,3.104 5.438,3.302 0.156,0.198 10 false 1 0.823,4.448 3.073,4.708 2.25,0.26 10 false : LIN Communication Line 4.979,3.74 5.927,3.958 0.948,0.219 10 false D24 4.979,3.948 6.958,4.323 1.979,0.375 10 false Steering Lock Actuator or Upper Bracket Assembly 5.479,3.219 5.938,3.417 0.458,0.198 10 false GND 5.49,2.375 5.948,2.573 0.458,0.198 10 false IG2 5.479,1.729 5.635,1.927 0.156,0.198 10 false B 5.479,0.906 5.938,1.104 0.458,0.198 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly, refer to the smart access system with push-button start (for start function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION



HINT:

When the communication between the steering lock actuator or upper bracket assembly and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Procedure1

a.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Result:
Result Proceed to
B2786 is not output A
B2786 is output B



Post-procedure1

a.

None



A

B

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the D24 steering lock actuator or upper bracket assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-1 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D24)Location & Routing

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D24-7 (B) - Body ground Ignition switch off 11 to 14 V
D24-6 (IG2) - D24-7 (B) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D24 steering lock actuator or upper bracket assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D86,D24)Location & Routing

Click Connector(D86)Instrument Panel>Instrument Panel Wire>Certification ECU

Click Connector(D24)Instrument Panel>Instrument Panel Wire>Steering Lock Actuator or Upper Bracket Assembly

D86-13 (LIN) - D24-5 (LIN) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR