Home › Power Source / Network › NETWORKING › CXPI COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455451 CXPI COMMUNICATION SYSTEM C

NETWORKING  CXPI COMMUNICATION SYSTEM  B12A0  Lost Communication with Illumination Module "A"  B12A1  Lost Communication with Illumination Module "B"  


DESCRIPTION

This DTC is stored when CXPI communication between the room light control relay and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B12A0 Lost Communication with Illumination Module "A" No communication between main body ECU (multiplex network body ECU) and room light control relay (for Front Side) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Room light control relay (for Front Side)

·

Harness or connector


Main Body A
B12A1 Lost Communication with Illumination Module "B" No communication between main body ECU (multiplex network body ECU) and room light control relay (for Rear Side) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

Room light control relay (for Rear Side)

·

Harness or connector


Main Body A

WIRING DIAGRAM

C424395E04
0.156,1.74 0.615,1.938 0.458,0.198 10 false D12 0.156,1.906 1.833,2.333 1.677,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1,1.406 1.458,1.604 0.458,0.198 10 false CXP2 1.458,1.219 1.917,1.417 0.458,0.198 10 false 11 3.24,2.125 3.698,2.323 0.458,0.198 10 false D115 3.229,2.271 5.885,2.552 2.656,0.281 10 false Room Light Control Relay (for Front Side) 3.479,1.698 3.938,1.896 0.458,0.198 10 false 9 3.698,1.802 4.156,2 0.458,0.198 10 false E 3.427,0.76 3.885,0.958 0.458,0.198 10 false 14 3.698,0.865 4.156,1.063 0.458,0.198 10 false ILA4 3.698,1.396 4.156,1.594 0.458,0.198 10 false CXPI 3.438,1.25 3.896,1.448 0.458,0.198 10 false 10 5.24,1.375 6.75,1.677 1.51,0.302 10 false to Reading Light Circuit 4.896,0.417 6.667,0.823 1.771,0.406 10 false from Auxiliary Battery 3.813,0.281 4.75,0.563 0.938,0.281 10 false DOME D 4.875,3.177 6.51,3.625 1.635,0.448 10 false from Auxiliary Battery 3.771,3.052 4.708,3.313 0.938,0.26 10 false DOME D 3.698,4.188 4.156,4.385 0.458,0.198 10 false CXPI 3.708,4.583 4.167,4.781 0.458,0.198 10 false BU- 3.49,4.438 3.948,4.635 0.458,0.198 10 false 9 3.417,4.031 3.875,4.229 0.458,0.198 10 false 10 3.49,3.531 3.948,3.729 0.458,0.198 10 false 7 3.708,3.656 4.167,3.854 0.458,0.198 10 false BU+ 5.24,4.177 6.417,4.667 1.177,0.49 10 false to Door Trim Light Circuit 0.813,6.448 2.74,6.813 1.927,0.365 10 false : CXPI Communication Line 3.333,4.875 3.792,5.073 0.458,0.198 10 false G76 3.333,5.073 5.99,5.354 2.656,0.281 10 false Room Light Control Relay (for Rear Side)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Result Proceed to
B12A0 and B12A1 are output A
B12A0 is output B
B12A1 is output C



Post-procedure1

a.

None



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Front Side])

B

3.CHECK HARNESS AND CONNECTOR (ROOM LIGHT CONTROL RELAY [for Front Side] POWER SOURCE CIRCUIT)

C

5.CHECK HARNESS AND CONNECTOR (ROOM LIGHT CONTROL RELAY [for Rear Side] POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Front Side])

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D115 room light control relay (for Front Side) connector.


c.

Disconnect the G76 room light control relay (for Rear Side) connector.


d.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D115,D12)Location & Routing

Click Connector(D115)Instrument Panel>Instrument Panel Wire>Room Light Control Relay

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

D115-10 (CXPI) - D12-11 (CXP2) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D115-10 (CXPI) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ROOM LIGHT CONTROL RELAY [for Front Side] POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the D115 room light control relay (for Front Side) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D115)Location & Routing

Click Connector(D115)Instrument Panel>Instrument Panel Wire>Room Light Control Relay

D115-9 (E) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D115)Location & Routing

Click Connector(D115)Instrument Panel>Instrument Panel Wire>Room Light Control Relay

D115-14 (ILA4) - Body ground Ignition switch off 10 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Front Side])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Front Side])

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D115 room light control relay (for Front Side) connector.


c.

Disconnect the G76 room light control relay (for Rear Side) connector.


d.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D115,D12)Location & Routing

Click Connector(D115)Instrument Panel>Instrument Panel Wire>Room Light Control Relay

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

D115-10 (CXPI) - D12-11 (CXP2) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D115-10 (CXPI) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE ROOM LIGHT CONTROL RELAY (for Front Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ROOM LIGHT CONTROL RELAY [for Rear Side] POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Disconnect the G76 room light control relay (for Rear Side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G76)Location & Routing

Click Connector(G76)Body>Floor Wire / No. 3 Floor Wire>Rear Room Light Control Relay

G76-9 (BU-) - Body ground Always Below 1 Ω



Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G76)Location & Routing

Click Connector(G76)Body>Floor Wire / No. 3 Floor Wire>Rear Room Light Control Relay

G76-7 (BU+) - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Rear Side])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - ROOM LIGHT CONTROL RELAY [for Rear Side])

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D115 room light control relay (for Front Side) connector.


c.

Disconnect the G76 room light control relay (for Rear Side) connector.


d.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G76,D12)Location & Routing

Click Connector(G76)Body>Floor Wire / No. 3 Floor Wire>Rear Room Light Control Relay

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

G76-10 (CXPI) - D12-11 (CXP2) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
G76-10 (CXPI) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE ROOM LIGHT CONTROL RELAY (for Rear Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR