Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Communication stop for "Main Body ECU" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Main body ECU (multiplex network body ECU) main wire or connector

·

Power source circuit of main body ECU (multiplex network body ECU) or driver side junction block assembly

·

Main body ECU (multiplex network body ECU) or driver side junction block assembly ground circuit

·

Main body ECU (multiplex network body ECU) or driver side junction block assembly



WIRING DIAGRAM

C387443E10
0.094,1.531 0.708,1.729 0.615,0.198 10 false D166 0.094,1.729 2.927,1.979 2.833,0.25 10 false No. 5 Global CAN Junction Connector 1.573,1.094 2.188,1.292 0.615,0.198 10 false 2 1.552,0.406 2.167,0.604 0.615,0.198 10 false 12 5.469,0.563 5.854,0.76 0.385,0.198 10 false D11 5.458,1.208 5.844,1.406 0.385,0.198 10 false D11 5.521,2.479 5.906,2.677 0.385,0.198 10 false A 5.51,3.531 5.896,3.729 0.385,0.198 10 false A 5.531,4.896 5.917,5.094 0.385,0.198 10 false A 5.531,7.167 5.917,7.365 0.385,0.198 10 false A 5.458,7.99 7.125,8.479 1.667,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 2.781,7.156 3.167,7.354 0.385,0.198 10 false 4D 2.76,6.469 3.146,6.667 0.385,0.198 10 false 4D 2.781,3.823 3.167,4.021 0.385,0.198 10 false 4D 2.771,3.083 3.156,3.281 0.385,0.198 10 false 4K 2.771,2.479 3.156,2.677 0.385,0.198 10 false 4L 2.792,2.26 3.177,2.458 0.385,0.198 10 false 1 2.813,2.854 3.198,3.052 0.385,0.198 10 false 1 2.771,3.563 3.156,3.76 0.385,0.198 10 false 18 2.75,6.25 3.135,6.448 0.385,0.198 10 false 19 2.813,6.906 3.198,7.104 0.385,0.198 10 false 7 0.156,3.781 1.99,4.583 1.833,0.802 10 false from Certification ECU (Smart Key ECU Assembly) 0.625,3.052 2.063,3.26 1.438,0.208 10 false from Auxiliary Battery 0.177,2.448 1.708,2.729 1.531,0.281 10 false from Auxiliary Battery 2.031,2.323 2.635,2.563 0.604,0.24 10 false J/B D-B 3.938,2.333 4.885,2.573 0.948,0.24 10 false ECU-B D NO.1 4.604,3.406 5.063,3.604 0.458,0.198 10 false ACC D 4.479,4.74 5.26,4.938 0.781,0.198 10 false IG1 D NO.4 3.521,6.719 4.302,6.917 0.781,0.198 10 false IG1 D NO.1 3.51,5.406 4.292,5.604 0.781,0.198 10 false IG1 D NO.2 3.604,4.073 4.385,4.271 0.781,0.198 10 false ACC D 5.51,0.323 5.896,0.521 0.385,0.198 10 false 1 5.531,0.99 5.917,1.188 0.385,0.198 10 false 2 5.833,0.542 6.219,0.74 0.385,0.198 10 false CANH 5.833,1.198 6.219,1.396 0.385,0.198 10 false CANL 5.854,2.49 6.24,2.688 0.385,0.198 10 false BECU 5.49,2.271 5.875,2.469 0.385,0.198 10 false 31 5.49,3.323 5.875,3.521 0.385,0.198 10 false 30 5.49,4.677 5.875,4.875 0.385,0.198 10 false 32 5.49,6.906 5.875,7.104 0.385,0.198 10 false 11 5.844,3.542 6.229,3.74 0.385,0.198 10 false ACC 5.865,7.156 6.25,7.354 0.385,0.198 10 false GND1 5.854,4.875 6.24,5.073 0.385,0.198 10 false IG 0.125,6.448 1.958,7.25 1.833,0.802 10 false from Certification ECU (Smart Key ECU Assembly) 3.146,8 5.219,8.354 2.073,0.354 10 false Driver Side Junction Block Assembly


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D11 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D11)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

D11-1 (CANH) - D11-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU).


b.

Reconnect the 4D,4K and 4L driver side junction connectors.


c.
C227508C39
1.531,0.552 1.917,0.792 0.385,0.24 3,1.073 2.76,0.438 2.76,0.438 2.646,0.438 true 3.094,1.115 3.01,1.594 3.01,1.594 2.875,1.594 true 2.917,1.083 2.74,0.771 2.74,0.771 2.625,0.771 true 1.219,1.083 1.135,0.771 1.135,0.771 1.021,0.771 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.667,0.604 1.979,0.76 0.313,0.156 10 false A 2.281,0.375 2.719,0.552 0.438,0.177 10 false BECU 2.333,0.719 2.771,0.896 0.438,0.177 10 false ACC 2.719,1.531 3.156,1.708 0.438,0.177 10 false IG 0.667,0.708 1.104,0.885 0.438,0.177 10 false GND1
*a Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



d.

Reconnect the cable to the negative (-) auxiliary battery terminal.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-31 (BECU) - Body ground Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground Ignition switch ACC 11 to 14 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 4L, 4K and 4D driver side junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-7 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4L-1 - Body ground Ignition switch off 11 to 14 V
4K-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4D-18 - Body ground Ignition switch ACC 11 to 14 V
4D-19 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG