Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

Rear television camera assembly branch wire or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly



WIRING DIAGRAM

C393727E03
0.521,5.219 3.427,5.417 2.906,0.198 10 false *1: w/ Panoramic View Monitor System 0.521,5.5 3.427,5.698 2.906,0.198 10 false *2: w/o Panoramic View Monitor System 5.677,1.01 6.271,1.167 0.594,0.156 10 false CANH 0.188,2.021 2.74,2.281 2.552,0.26 10 false No. 13 Global CAN Junction Connector 1.74,0.906 2.125,1.073 0.385,0.167 10 false 5 1.719,1.49 2.104,1.656 0.385,0.167 10 false 15 0.188,1.854 0.573,2.021 0.385,0.167 10 false G128 5.667,1.604 6.26,1.76 0.594,0.156 10 false CANL 4.854,1.021 5.448,1.177 0.594,0.156 10 false K12 4.844,1.604 5.438,1.76 0.594,0.156 10 false K12 5.313,1.01 5.906,1.167 0.594,0.156 10 false K4 5.313,1.604 5.906,1.76 0.594,0.156 10 false K4 4.844,2.635 5.438,2.792 0.594,0.156 10 false K12 4.844,4.052 5.438,4.208 0.594,0.156 10 false K12 5.302,2.635 5.896,2.792 0.594,0.156 10 false K4 5.302,4.052 5.896,4.208 0.594,0.156 10 false K4 0.51,3.094 3.052,3.438 2.542,0.344 10 false from Integration Control Sub-Assembly*3, Radio Receiver Assembly*4 1.313,2.656 3.115,2.823 1.802,0.167 10 false from Parking Assist ECU*1 1.344,4.042 3.229,4.229 1.885,0.188 10 false from Parking Assist ECU*1 5.688,2.615 6.281,2.771 0.594,0.156 10 false CB+ 5.677,4.042 6.271,4.198 0.594,0.156 10 false CGND 5.292,0.792 5.677,0.958 0.385,0.167 10 false 4*2 5.292,1.375 5.677,1.542 0.385,0.167 10 false 1*2 5.281,2.406 5.667,2.573 0.385,0.167 10 false 6*2 5.281,3.823 5.667,3.99 0.385,0.167 10 false 5*2 4.865,0.792 5.25,0.958 0.385,0.167 10 false 1*1 4.865,1.375 5.25,1.542 0.385,0.167 10 false 2*1 4.875,2.406 5.26,2.573 0.385,0.167 10 false 4*1 4.865,3.823 5.25,3.99 0.385,0.167 10 false 3*1 4.958,4.823 7.094,5.125 2.135,0.302 10 false Rear Television Camera Assembly 0.573,4.521 3.115,4.865 2.542,0.344 10 false from Integration Control Sub-Assembly*3, Radio Receiver Assembly*4 3.427,5.24 6.333,5.438 2.906,0.198 10 false *3: w/ Navigation System 3.854,4.417 4.24,4.583 0.385,0.167 10 false *2 3.854,2.99 4.24,3.156 0.385,0.167 10 false *2 3.865,2.479 4.25,2.646 0.385,0.167 10 false *1 3.844,3.917 4.229,4.083 0.385,0.167 10 false *1 3.417,5.51 6.323,5.708 2.906,0.198 10 false *4: w/o Navigation System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K12*1 or K4*2 rear television camera assembly connector.

*1: w/ Panoramic View Monitor System

*2: w/o Panoramic View Monitor System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panoramic View Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(K12)Location & Routing

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K12-1 (CANH) - K12-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

w/o Panoramic View Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(K4)Location & Routing

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K4-4 (CANH) - K4-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panoramic View Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(K12)Location & Routing

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K12-3 (CGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω

w/o Panoramic View Monitor System
Tester Connection Condition Specified Condition

Click Location & Routing(K4)Location & Routing

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K4-5 (CGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Panoramic View Monitor System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K12)Location & Routing

Click Connector(K12)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K12-4 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V

w/o Panoramic View Monitor System
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K4)Location & Routing

Click Connector(K4)Body>No. 1 Back Door Wire>Rear Television Camera Assembly

K4-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result Proceed to
OK A
NG (w/ Panoramic View Monitor System) B
NG (w/o Panoramic View Monitor System) C



A

B

C