Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  FC Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
FC control ECU Communication Stop Mode Communication stop for "FC" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

FC control ECU main wire or connector

·

Power source circuit of FC control ECU

·

FC control ECU ground circuit

·

FC control ECU



WIRING DIAGRAM

C441460E03
0.094,1.156 2.781,1.594 2.688,0.438 10 false No. 7 Global CAN Junction Connector 0.135,0.958 0.604,1.25 0.469,0.292 10 false D173 1.271,2.042 3.365,2.469 2.094,0.427 10 false from FC-B Relay 2.927,1.948 3.646,2.406 0.719,0.458 10 false FC-B NO.2 5.229,2.542 5.948,3 0.719,0.458 10 false A48 5.24,3.969 5.948,4.344 0.708,0.375 10 false A48 5.271,3.156 5.979,3.531 0.708,0.375 10 false B1 5.25,2.063 5.969,2.521 0.719,0.458 10 false B1 5.26,1.573 5.979,2.031 0.719,0.458 10 false B1 5.271,0.354 5.99,0.813 0.719,0.458 10 false B1 5.271,0.781 5.99,1.24 0.719,0.458 10 false B1 5.24,4.375 5.948,4.75 0.708,0.375 10 false A48 5.563,4 6.271,4.375 0.708,0.375 10 false EC 5.563,4.417 6.271,4.792 0.708,0.375 10 false E03 5.604,0.25 6.198,0.542 0.594,0.292 10 false CA1H 5.594,0.906 6.313,1.365 0.719,0.458 10 false CA1L 1.594,0.281 2.313,0.74 0.719,0.458 10 false 17 1.625,0.708 2.344,1.167 0.719,0.458 10 false 7 5.563,3.125 6.281,3.583 0.719,0.458 10 false E1 5.573,2.563 6.292,3.021 0.719,0.458 10 false BP3 5.563,2.073 6.052,2.385 0.49,0.313 10 false +B2 5.563,1.604 6.052,1.917 0.49,0.313 10 false +B1 5.26,0.198 5.979,0.656 0.719,0.458 10 false 65 5.271,0.604 5.99,1.063 0.719,0.458 10 false 64 5.25,1.385 5.969,1.844 0.719,0.458 10 false 43 5.271,1.865 5.99,2.323 0.719,0.458 10 false 83 5.302,2.344 6.021,2.802 0.719,0.458 10 false 2 5.229,2.958 5.948,3.417 0.719,0.458 10 false 104 5.271,3.781 6,4.104 0.729,0.323 10 false 53 5.271,4.198 5.99,4.656 0.719,0.458 10 false 21 5.531,4.917 6.875,5.323 1.344,0.406 10 false FC Control ECU 1.281,2.542 2.448,2.802 1.167,0.26 10 false from FC-B Relay 2.938,2.438 3.656,2.896 0.719,0.458 10 false FC-B NO.4 5.281,3.563 5.99,3.938 0.708,0.375 10 false B1 5.25,3.375 5.969,3.833 0.719,0.458 10 false 105 5.594,3.583 6.125,3.802 0.531,0.219 10 false E2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (FC CONTROL ECU MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B1 FC control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-65 (CA1H) - B1-64 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU POWER SOURCE CIRCUIT)
a.

Disconnect the A48 FC control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B1)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

A48-53 (EC) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A48-21 (E03) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
B1-104 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
B1-105 (E2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A48,B1)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

A48-2 (BP3) - Body ground Ignition switch ON 11 to 14 V
B1-43 (+B1) - Body ground Ignition switch ON 11 to 14 V
B1-83 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR