Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  EV Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
EV control ECU Communication Stop Mode Communication stop for "EV" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

EV control ECU branch line or connector

·

Power source circuit of EV control ECU

·

EV control ECU ground circuit

·

EV control ECU assembly



WIRING DIAGRAM

C452900E01
5.396,5.75 5.854,5.948 0.458,0.198 10 false A55 5.76,0.583 6.219,0.781 0.458,0.198 10 false CA1H 5.771,1.052 6.229,1.25 0.458,0.198 10 false CA1L 5.76,1.948 6.219,2.146 0.458,0.198 10 false +B1 5.781,2.979 6.24,3.177 0.458,0.198 10 false AM21 5.448,0.385 5.906,0.583 0.458,0.198 10 false 25 5.448,0.865 5.906,1.063 0.458,0.198 10 false 26 5.438,2.198 5.896,2.396 0.458,0.198 10 false 11 5.813,4.958 6.271,5.156 0.458,0.198 10 false E02 1.844,0.469 2.302,0.667 0.458,0.198 10 false 14 1.854,0.948 2.313,1.146 0.458,0.198 10 false 4 0.25,1.188 0.708,1.385 0.458,0.198 10 false D173 0.26,1.354 2.625,1.75 2.365,0.396 10 false No. 7 Global CAN Junction Connector 3.844,2.25 5.042,2.469 1.198,0.219 10 false IGCT NO.5 5.667,6.271 6.865,6.563 1.198,0.292 10 false EV Control ECU 5.771,2.396 6.229,2.594 0.458,0.198 10 false +B2 2.135,2.333 3.531,2.531 1.396,0.198 10 false from IG Relay 5.438,1.813 5.896,2.01 0.458,0.198 10 false 23 5.417,2.771 5.875,2.969 0.458,0.198 10 false 11 5.771,4.615 6.229,4.813 0.458,0.198 10 false E01 1.677,3.354 3.302,3.656 1.625,0.302 10 false from IGR-NO.1 Relay 3.885,3.885 5.083,4.104 1.198,0.219 10 false IG2 P NO.1 3.729,3.26 4.927,3.479 1.198,0.219 10 false MPX-B P NO.1 5.781,4.042 6.24,4.24 0.458,0.198 10 false IG2 5.427,3.792 5.885,3.99 0.458,0.198 10 false 10 1.313,3.99 3.208,4.292 1.896,0.302 10 false from EFI-MAIN NO.1 Relay 5.396,5.354 5.854,5.552 0.458,0.198 10 false A56 5.385,4.969 5.844,5.167 0.458,0.198 10 false A56 5.406,4.573 5.865,4.771 0.458,0.198 10 false A56 5.396,4 5.854,4.198 0.458,0.198 10 false A56 5.375,3.365 5.833,3.563 0.458,0.198 10 false A55 5.396,2.979 5.854,3.177 0.458,0.198 10 false A56 5.396,2.385 5.854,2.583 0.458,0.198 10 false A55 5.396,1.99 5.854,2.188 0.458,0.198 10 false A56 5.396,1.052 5.854,1.25 0.458,0.198 10 false A56 5.396,0.573 5.854,0.771 0.458,0.198 10 false A56 5.802,3.417 6.26,3.615 0.458,0.198 10 false AM22 5.427,3.177 5.885,3.375 0.458,0.198 10 false 12 5.458,4.365 5.917,4.563 0.458,0.198 10 false 27 5.438,4.781 5.896,4.979 0.458,0.198 10 false 28 5.438,5.188 5.896,5.385 0.458,0.198 10 false 14 5.427,5.563 5.885,5.76 0.458,0.198 10 false 16 5.792,5.802 6.25,6 0.458,0.198 10 false E16 5.792,5.396 6.25,5.594 0.458,0.198 10 false E1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (EV CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D15 EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-16 (CA1H) - D15-17 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU POWER SOURCE CIRCUIT)
a.

Disconnect the A16 and A17 EV control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-3 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A17-4 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D15-4 (E12) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D15-5 (E02) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A16,D15)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A16-7 (IG2) - GND Ignition switch ON 11 to 14 V
D15-1 (BATT) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR