Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Shift Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Shift Control ECU Communication Stop Mode Communication stop for "Transmission Control" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Shift control ECU branch wire or connector

·

Power source circuit of shift control ECU

·

Shift control ECU ground circuit

·

Shift control ECU



WIRING DIAGRAM

C368274E11
5.615,6.135 6.073,6.333 0.458,0.198 10 false E01 5.604,6.656 6.063,6.854 0.458,0.198 10 false E02 5.604,7.167 6.063,7.365 0.458,0.198 10 false E03 5.604,7.667 6.063,7.865 0.458,0.198 10 false EC 1.635,0.26 2.094,0.458 0.458,0.198 10 false 13 5.604,5.667 6.063,5.865 0.458,0.198 10 false E12 5.615,1.615 6.073,1.813 0.458,0.198 10 false IGCT 5.604,2.188 6.063,2.385 0.458,0.198 10 false BATT 5.24,1.615 5.698,1.813 0.458,0.198 10 false D92 5.615,3.323 6.073,3.521 0.458,0.198 10 false ACC 5.615,3.896 6.073,4.094 0.458,0.198 10 false BUB 5.25,2.76 5.708,2.958 0.458,0.198 10 false D92 5.604,2.75 6.063,2.948 0.458,0.198 10 false IG2 5.24,3.323 5.698,3.521 0.458,0.198 10 false D92 5.24,3.885 5.698,4.083 0.458,0.198 10 false D92 5.25,0.396 5.708,0.594 0.458,0.198 10 false D92 5.25,0.979 5.708,1.177 0.458,0.198 10 false D92 5.25,5.167 5.708,5.365 0.458,0.198 10 false D92 5.24,7.656 5.698,7.854 0.458,0.198 10 false D92 5.24,7.156 5.698,7.354 0.458,0.198 10 false D93 5.24,6.677 5.698,6.875 0.458,0.198 10 false D93 5.24,6.146 5.698,6.344 0.458,0.198 10 false D93 5.24,5.656 5.698,5.854 0.458,0.198 10 false D93 5.24,2.188 5.698,2.385 0.458,0.198 10 false D93 5.615,0.375 6.073,0.573 0.458,0.198 10 false CA1H 5.615,0.969 6.073,1.167 0.458,0.198 10 false CA1L 5.51,7.99 6.74,8.24 1.229,0.25 10 false Shift Control ECU 0.177,1.063 0.635,1.26 0.458,0.198 10 false D173 0.177,1.229 2.917,1.51 2.74,0.281 10 false No. 7 Global CAN Junction Connector 1.646,0.875 2.104,1.073 0.458,0.198 10 false 3 5.323,0.208 5.781,0.406 0.458,0.198 10 false 9 5.313,0.781 5.771,0.979 0.458,0.198 10 false 8 5.333,4.948 5.792,5.146 0.458,0.198 10 false 1 5.615,5.167 6.073,5.365 0.458,0.198 10 false E1 5.313,5.948 5.771,6.146 0.458,0.198 10 false 6 5.313,6.479 5.771,6.677 0.458,0.198 10 false 5 5.313,6.969 5.771,7.167 0.458,0.198 10 false 4 5.281,5.469 5.74,5.667 0.458,0.198 10 false 17 5.281,7.448 5.74,7.646 0.458,0.198 10 false 11 5.281,1.417 5.74,1.615 0.458,0.198 10 false 20 5.281,2.573 5.74,2.771 0.458,0.198 10 false 27 5.313,1.969 5.771,2.167 0.458,0.198 10 false 1 5.281,3.135 5.74,3.333 0.458,0.198 10 false 18 5.281,3.698 5.74,3.896 0.458,0.198 10 false 10 3.802,3.188 4.625,3.49 0.823,0.302 10 false ACC P NO.1 3.688,3.76 4.719,4.063 1.031,0.302 10 false P CON MAIN 2 3.813,2.625 4.844,2.927 1.031,0.302 10 false IG2 P NO.2 3.823,1.49 4.646,1.792 0.823,0.302 10 false IGCT NO.5 3.75,2.052 4.573,2.354 0.823,0.302 10 false P CON MAIN 1.365,2.156 2.927,2.438 1.563,0.281 10 false from Auxiliary Battery 1.313,3.896 2.771,4.208 1.458,0.313 10 false Sub Battery Assembly 1.604,2.708 3.021,2.969 1.417,0.26 10 false from IG2 P Relay 1.552,3.281 2.969,3.573 1.417,0.292 10 false from ACC P Relay 1.281,1.594 2.75,1.823 1.469,0.229 10 false from IGCT NO. 2 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SHIFT CONTROL ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D92 shift control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-9 (CA1H) - D92-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the D93 shift control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D92,D93)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-1 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D93-17 (E12) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D93-6 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D93-5 (E02) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D93-4 (E03) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
D92-11 (EC) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*: Power is supplied from the sub-battery assembly with control for only 5 seconds after the ignition switch is turned to ON. Therefore, measure the voltage during that time.

Click Location & Routing(D93,D92)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D93-1 (BATT) - Body ground Always 8 to 15.4 V
D92-10 (BUB) - Body ground 5 seconds after ignition switch ON* 8 to 15.4 V
D92-18 (ACC) - Body ground Ignition switch ACC 6 V or higher
Ignition switch off Below 1 V
D92-27 (IG2) - Body ground Ignition switch ON 6 V or higher
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)