Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2020.11–2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Rear Door ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Door ECU LH Communication Stop Mode Communication stop for "Rear Door LH (RL-Door) /RL Door / LH PSD" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Rear multiplex network door ECU LH branch wire or connector

·

Power source circuit of rear multiplex network door ECU LH

·

Rear multiplex network door ECU LH ground circuit

·

Rear multiplex network door ECU LH



WIRING DIAGRAM

C453296E05
5.656,1 6.271,1.198 0.615,0.198 10 false CANP 5.646,1.51 6.26,1.708 0.615,0.198 10 false CANN 5.646,2.375 6.26,2.573 0.615,0.198 10 false SIG 5.646,3.125 6.26,3.323 0.615,0.198 10 false CPUB 5.656,3.844 6.271,4.042 0.615,0.198 10 false BDR 5.656,4.375 6.271,4.573 0.615,0.198 10 false GND 3.969,2.219 4.781,2.448 0.813,0.229 10 false IG1 P NO.2 1.542,0.885 2.156,1.083 0.615,0.198 10 false 3 1.542,1.406 2.156,1.604 0.615,0.198 10 false 9 5.427,0.885 6.042,1.083 0.615,0.198 10 false 8 5.417,1.406 6.031,1.604 0.615,0.198 10 false 7 5.354,2.25 5.969,2.448 0.615,0.198 10 false 12 5.354,3.01 5.969,3.208 0.615,0.198 10 false 11 5.417,3.74 6.031,3.938 0.615,0.198 10 false 4 5.417,4.271 6.031,4.469 0.615,0.198 10 false 1 4.677,5.042 5.292,5.24 0.615,0.198 10 false F16 4.667,5.208 7.094,5.719 2.427,0.51 10 false Rear Multiplex Network Door ECU LH 0.156,1.76 0.771,1.958 0.615,0.198 10 false G132 0.156,1.938 1.885,2.344 1.729,0.406 10 false No. 14 Global CAN Junction Connector 3.969,3.698 4.823,4.083 0.854,0.385 10 false DOOR R/L1 3.875,2.969 4.906,3.167 1.031,0.198 10 false MPX-B P NO.1 1.573,2.354 3.26,2.958 1.688,0.604 10 false from IG1 P NO.1 Relay 1.688,3.115 3.083,3.344 1.396,0.229 10 false from Auxiliary Battery 1.688,3.833 3.104,4.115 1.417,0.281 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (REAR MULTIPLEX NETWORK DOOR ECU LH BRANCH WIRE)
a.

Cable disconnected from negative (-) auxiliary battery terminal.


b.

Disconnect the F16 rear multiplex network door ECU LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F16)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F16-8 (CANP) - F16-7 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(F16)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F16-1 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(F16)Location & Routing

Click Connector(F16)Body>No. 1 Rear Door Wire / No. 2 Rear Door Wire>Rear Multiplex Network Door ECU LH

F16-12 (SIG) - Body ground Ignition switch ON 11 to 14 V
F16-4 (BDR) - Body ground Ignition switch off 11 to 14 V
F16-11 (CPUB) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR MULTIPLEX NETWORK DOOR ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)