Home › General › MAINTENANCE › FRONT BRAKE FLEXIBLE HOSE
RM37H0E _V1 General _095083 MAINTENANCE _0455455 FRONT BRAKE FLEXIBLE HOSE A

MAINTENANCE  FRONT BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C450102N03
5.833,0.417 6.677,0.583 0.844,0.167 5.792,0.365 6.708,0.625 0.917,0.26 1.75,0.875 2.667,1.208 0.917,0.333 1.708,0.813 2.698,1.26 0.99,0.448 0.115,2.708 0.885,2.875 0.771,0.167 0.083,2.656 0.927,2.927 0.844,0.271 4.833,1.833 4.667,1.833 4.667,1.833 4.594,2.063 true 5.833,0.5 5.5,0.5 5.5,0.5 5.5,0.917 true 6.5,1.104 6.333,1.104 6.333,1.104 6.26,1.333 true 2.854,3.458 1.667,4.927 1.667,4.927 1.5,4.927 true 2.667,1.042 3.083,1.042 true 0.896,2.792 1.427,2.792 true 1.25,2.802 1.25,3.844 true 1.313,4.802 1.594,5.156 0.281,0.354 18 false 1 4.917,1.771 5.188,1.99 0.271,0.219 10 false ● 5.792,0.656 6.292,0.906 0.5,0.25 10 false ●*1 6.573,1.031 6.99,1.323 0.417,0.292 10 false ●*2 1.792,0.906 2.615,1.073 0.823,0.167 8 false 15.2 (155, 11) 1.792,1.052 2.646,1.229 0.854,0.177 8 false 13.4 (137, 10)* 5.906,0.448 6.719,0.625 0.813,0.177 8 false 39.2 (400, 29) 0.208,2.708 0.938,2.906 0.729,0.198 8 false 20 (204, 15) 1.688,1.302 2.073,1.542 0.385,0.24 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT FLEXIBLE HOSE 47313J (Click here) - -

*1 UNION BOLT *2 GASKET
*3 BRAKE TUBE - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

C437797N02
6.51,0.198 6.865,0.198 true 6.521,0.604 6.802,0.604 true 5.521,2.469 5.667,2.083 5.667,2.083 5.833,2.083 true 6.302,0.479 6.573,0.76 0.271,0.281 18 false 5 5.906,1.948 6.271,2.313 0.365,0.365 18 false 4 6.052,0.073 6.573,0.354 0.521,0.281 18 false 2, 3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 BLEED BRAKE LINE - - - (Click here)
4 FRONT WHEEL - - - -
5 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the left and right front flexible hoses are not interchangeable, verify the part number when installing the front flexible hoses.

·

When reusing the front flexible hoses, use the identification marks created during removal to install each front flexible hose to its original position.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47313J 1.INSTALL FRONT FLEXIBLE HOSE

Z101186

NOTICE:

When installing the front flexible hose, minimize twisting of the hose.



a.
C450104C01
2.344,2.083 2.594,2.083 true 1.167,0.583 1.25,0.583 1.25,0.583 1.333,0.75 true 3.833,0.104 4.208,0.438 0.375,0.333 18 false iii 2.656,1.99 2.875,2.198 0.219,0.208 10 true *a 1.927,0.323 2.146,0.531 0.219,0.208 10 false *c 0.948,0.51 1.167,0.719 0.219,0.208 10 false *b 0.375,0.063 0.917,0.396 0.542,0.333 18 false i, ii 2,3.125 2.375,3.458 0.375,0.333 18 false iv
*a Identification Mark *b Union Nut Wrench
*c Torque Wrench Fulcrum Length - -


i.

Install the front flexible hose with a new clip.

NOTICE:
·

Install the clip as far as it will go.

·

When installing the front flexible hose, face the identification mark to the outside of the vehicle.




ii.

Using a union nut wrench, connect the brake line to the front flexible hose while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




iii.

Install the front flexible hose and front speed sensor to the front shock absorber assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



iv.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:
·

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.

·

Do not twist the front flexible hose when installing it.





Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

Click here(Click here)

Hide 4.INSTALL FRONT WHEEL

Hide 5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART