Home › Brake › BRAKE (REAR) › REAR BRAKE
RM37H0E _54 Brake _097303 BRAKE (REAR) _0455483 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C450070N04
1.333,1.823 2.177,2.01 0.844,0.188 1.292,1.76 2.219,2.052 0.927,0.292 0.75,0.229 1.75,0.448 1,0.219 0.708,0.177 1.802,0.51 1.094,0.333 5.521,2.365 5.667,1.542 5.667,1.542 5.917,1.542 true 6.781,4.073 6.698,4.073 6.698,4.073 6.615,4.323 true 2.406,4.958 2.573,4.958 2.573,4.958 2.854,4.354 true 1.167,3.719 1.417,3.719 1.417,3.719 1.594,3.198 true 1.333,1.917 1.042,1.917 1.042,1.917 1.042,2.354 true 0.573,2.948 0.844,2.948 true 1.75,0.333 2,0.333 2,0.333 2,0.5 true 0.927,3.573 1.24,3.875 0.313,0.302 18 false 4 2.177,4.813 2.458,5.167 0.281,0.354 18 false 3 6.854,3.917 7.135,4.271 0.281,0.354 18 false 2 6.292,1.406 6.74,1.844 0.448,0.438 18 false 1 1.313,2.083 1.781,2.333 0.469,0.25 10 false ● *1 0.229,2.854 0.719,3.208 0.49,0.354 10 false ● *2 2.219,0.417 2.5,0.604 0.281,0.188 10 false x 2 1.385,1.833 2.26,2.083 0.875,0.25 8 false 39.2 (400, 29) 0.823,0.26 1.958,0.458 1.135,0.198 8 false 151 (1540, 111)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC LH 42432 (Click here) - -
2 PARKING BRAKE SHOE ADJUSTING HOLE PLUG 42491 - - -
3 REAR DISC BRAKE CYLINDER ASSEMBLY LH 47850 - - -
4 REAR FLEXIBLE HOSE LH 47319F (Click here) - -

*1 UNION BOLT *2 GASKET
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part

C450044N04
3.667,4.333 5.271,5.646 1.604,1.313 0.083,2.667 1.563,3.969 1.479,1.302 1.688,3.469 3.438,5.042 1.75,1.573 1.281,0.781 3.958,2.365 2.677,1.583 2.438,4.854 2.438,4.188 true 2.01,4.854 2.844,4.854 2.844,4.854 2.844,4.604 true 4.344,4.75 4.094,4.75 true 4.521,5.385 4.323,5.385 true 0.854,3.583 1.104,3.583 true 0.698,2.927 0.948,2.927 true 3,2.083 3,1.25 3,1.25 2.667,1.25 true 2.656,1.833 2.99,1.833 false 1.719,1.417 1.969,1.417 true 3.521,2.667 2.354,2.667 2.354,2.667 2.354,2.729 true 3.052,3.104 3.052,2.677 true 4.667,4.083 4.5,4.083 4.5,4.083 4.5,4.333 false 1.146,3.969 1.146,4.354 1.146,4.354 0.979,4.354 false 2.604,5.052 2.604,5.354 2.604,5.354 2.438,5.354 false 3.385,1.5 3.635,1.5 true 0.938,1.25 1.271,1.25 false 4.406,4.667 4.719,4.865 0.313,0.198 10 false *1 0.635,3.51 0.896,3.708 0.26,0.198 10 false *1 1.021,2.865 1.292,3.104 0.271,0.24 10 false *2 4.104,5.323 4.323,5.521 0.219,0.198 10 false *2 1.49,1.333 1.781,1.615 0.292,0.281 10 false *3 2.938,2.156 3.229,2.438 0.292,0.281 10 false *4 3.708,1.406 4,1.688 0.292,0.281 10 false *5 3.615,2.604 3.906,2.885 0.292,0.281 10 false *6 2.198,5.208 2.5,5.521 0.302,0.313 18 false 6 5.042,3.948 5.354,4.281 0.313,0.333 18 false 5 0.708,4.188 1.021,4.521 0.313,0.333 18 false 5 1.781,4.771 2.094,4.969 0.313,0.198 10 false *7 0.698,1.104 1.01,1.438 0.313,0.333 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR DISC BRAKE ANTI-SQUEAL SHIM 04946 (Click here) - -
6 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
7 REAR DISC BRAKE FITTING KIT 04948 - - -

*1 NO. 1 ANTI-SQUEAL SHIM *2 NO. 2 ANTI-SQUEAL SHIM
*3 PIN HOLD CLIP *4 HOLE PIN
*5 NO. 1 ANTI-RATTLE SPRING *6 INNER ANTI-RATTLE SPRING
*7 REAR DISC BRAKE PAD - -
V100135

Disc brake grease
V100136

Grease

C450043N02
6.438,0.188 6.854,0.188 false 6.458,0.604 6.813,0.604 false 4.667,1.24 4.792,1.01 4.792,1.01 4.958,1.01 true 6.479,1.052 6.833,1.052 false 6.208,0.052 6.49,0.365 0.281,0.313 18 false 8 5.031,0.875 5.365,1.229 0.333,0.354 18 false 11 5.344,0.469 6.5,0.938 1.156,0.469 18 false 10, 12, 13 6.25,0.906 6.542,1.188 0.292,0.281 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

8 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
9 BLEED BRAKE LINE - - (Click here) -
10 ADJUST PARKING BRAKE - - - (Click here)
11 REAR WHEEL - - - -
12 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)
13 PARKING BRAKE SHOE BEDDING - - - (Click here)

CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42432 1.INSTALL REAR DISC LH

a.
C452032C01
3.74,0.917 4.333,0.917 true 3.729,0.865 4.063,0.865 4.063,0.865 4.063,0.917 true 4.385,0.844 4.604,1.052 0.219,0.208 10 true *a 0.438,0.052 1.375,0.417 0.938,0.365 18 false i, ii, iii
*a Matchmark - -


i.

When reusing the rear disc LH:

Align the matchmarks of the rear disc and rear axle hub and bearing assembly LH, and install the rear disc LH.


ii.

When replacing the rear disc LH:

Inspect the rear disc runout.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



iii.

Temporarily install the 5 hub nuts.



Hide 42491 2.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 47850 3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY LH

Torque:
151 N*m (1540 kgf*cm, 111 ft.*lbf)

Hide 47319F 4.CONNECT REAR FLEXIBLE HOSE LH

a.
C450054N01
0.406,0.042 0.688,0.396 0.281,0.354 18 false i

i.

Connect the rear flexible hose to the rear disc brake cylinder assembly LH with a new union bolt and a new gasket.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly LH.




Hide 04946 5.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Z101186

Click here(Click here)

Hide 04466 6.INSTALL REAR DISC BRAKE PAD KIT

Z101186

Click here(Click here)

Hide 04948 7.CONNECT REAR DISC BRAKE FITTING KIT

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.
C452031N02
0.427,0.052 0.927,0.333 0.5,0.281 18 false i, ii

i.

Connect the reservoir level switch connector.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>INSTALLATION


iii.

Perform the following procedure if air bleeding is not necessary:

1. Turn the ignition switch to ON (READY).

2. Depress the brake pedal and release it.

3. Clear the DTCs.



Hide 9. BLEED BRAKE LINE

Hide 10.ADJUST PARKING BRAKE

Hide 11.INSTALL REAR WHEEL

Hide 12. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 13. PARKING BRAKE SHOE BEDDING