Home › General › MAINTENANCE › REAR BRAKE FLEXIBLE HOSE
RM37H0E _V1 General _095083 MAINTENANCE _0455456 REAR BRAKE FLEXIBLE HOSE A

MAINTENANCE  REAR BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C450105N05
0.583,2.823 1.417,3.031 0.833,0.208 0.531,2.771 1.458,3.083 0.927,0.313 1.323,0.656 2.229,1.042 0.906,0.385 1.271,0.573 2.281,1.104 1.01,0.531 2.25,4.833 2.083,4.833 2.083,4.833 1.906,4.563 true 2.365,3.865 3.219,3.865 true 1.417,2.917 1.719,2.917 true 4.188,1.281 4.49,1.281 true 2.75,0.833 2.25,0.833 true 2.125,3.719 2.448,4.135 0.323,0.417 21 false 1 0.563,3.125 0.969,3.344 0.406,0.219 10 false ● *1 4.552,1.177 4.854,1.396 0.302,0.219 10 false ● 1.323,1.146 1.729,1.365 0.406,0.219 10 false *3 2.333,4.729 3,5.104 0.667,0.375 10 false ● *2 0.635,2.844 1.542,3.01 0.906,0.167 8 false 39.2 (400, 29) 1.385,0.677 2.469,0.927 1.083,0.25 8 false 15.2 (155, 11) 1.396,0.844 2.375,1.01 0.979,0.167 8 false 13.4 (137, 10)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR FLEXIBLE HOSE LH 47319F (Click here) - -

*1 UNION BOLT *2 GASKET
*3 BRAKE TUBE *4 HOLE PIN
● Non-reusable part - -

C450043N07
6.438,0.188 6.854,0.188 false 6.458,0.604 6.813,0.604 false 4.667,1.24 4.792,1.01 4.792,1.01 4.958,1.01 true 6.479,1.052 6.833,1.052 false 6.208,0.052 6.49,0.365 0.281,0.313 18 false 2 5.073,0.875 5.406,1.229 0.333,0.354 18 false 4 6.208,0.469 6.531,0.771 0.323,0.302 18 false 5 6.229,0.938 6.458,1.198 0.229,0.26 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 BLEED BRAKE LINE - - (Click here) -
4 REAR WHEEL - - - -
5 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

NOTICE:
·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

If both left and right rear flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47319F 1.INSTALL REAR FLEXIBLE HOSE LH

Z101186

NOTICE:

When installing the rear flexible hose, minimize twisting of the hose.



a.
C450107C02
1.083,0.583 1.167,0.583 1.167,0.583 1.281,0.719 true 1.875,0.292 2.188,0.49 0.313,0.198 10 false *a 0.917,0.5 1.229,0.698 0.313,0.198 10 false *b 3.938,0.031 4.25,0.313 0.313,0.281 18 false iii 0.385,0.042 0.781,0.323 0.396,0.281 18 false i, ii
*a Torque Wrench Fulcrum Length *b Union Nut Wrench


i.

Install the rear flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



ii.

Using a union nut wrench, connect the brake line to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




iii.

Install the rear flexible hose LH to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

Click here(Click here)

Hide 4.INSTALL REAR WHEEL

Hide 5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART