Home › Brake › PARKING BRAKE › FORCED RELEASE
RM37H0E _54 Brake _096946 PARKING BRAKE _0455458 FORCED RELEASE A

PARKING BRAKE  FORCED RELEASE  OPERATION METHOD  


CAUTION / NOTICE / HINT

CAUTION:
C388708

·

If work is performed without first securing the vehicle, the vehicle may start moving and cause a serious accident or other disaster. Therefore, be sure to apply the use wheel chocks to secure the vehicle before performing work.

·

Work on a level surface to ensure safety.



HINT:

The following procedure is for when using electric release SST.


PROCEDURE

Hide 2. SECURE VEHICLE

a.

Press the parking switch with the ignition switch turned on (IG) to activate the parking lock.


b.

Turn the ignition switch off and use wheel chocks to secure the vehicle.


Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

a.
C450129

Remove the luggage trim service hole cover.


Hide 4. PARKING BRAKE FORCED RELEASE

NOTICE:
C450130

·

When moving the vehicle after the forced release of the parking brake, install all parts except the connector shown in the illustration.

·

A DTC may be output when the ignition switch is turned on (IG) or (READY) when the connector shown in the illustration is disconnected. Clear the DTCs after performing the work.

·

If the DTCs are cleared but do not disappear:

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>FAIL-SAFE CHART



a.
C450130

Disconnect the connector shown in the illustration.


b.

Connect SST to SST.

SST
09756-48020  09756-48070  

HINT:

When using SST (09756-48070), use 2 of the 3 connectors.


C455188C02
2.01,4.26 2.229,4.26 2.229,4.26 2.76,4.896 true 5.031,1.667 5.198,1.667 5.198,1.667 5.365,1.417 true 5.635,0.469 5.885,0.469 true 5.385,8.177 5.688,7.75 5.688,7.75 5.875,7.75 false 4.24,7.427 4.688,6.917 4.688,6.917 4.875,6.917 true 1.74,1.24 2.073,1.24 false 0.844,1.417 1.177,1.417 false 1.698,4.146 1.948,4.375 0.25,0.229 10 true *a 4.781,1.573 4.99,1.74 0.208,0.167 10 true *b 0.438,0.406 0.75,0.563 0.313,0.156 10 false *c 4.938,6.833 5.188,7.01 0.25,0.177 10 false *d 2.167,1.177 2.479,1.333 0.313,0.156 10 false *e 0.604,1.344 0.917,1.5 0.313,0.156 10 false *f 5.958,0.385 6.156,0.573 0.198,0.188 10 true *c 5.938,7.677 6.135,7.865 0.198,0.188 10 true *c
*a Brake Pedal *b Auxiliary Battery
*c SST (09756-48020) *d SST (09756-48070)
*e Release Button *f FINISHED Light
V100135

Connector - -



c.

Connect SST to the parking brake ECU assembly connector inside of the vehicle.

SST
09756-48070  


d.

Connect SST to the auxiliary battery inside of the vehicle.

SST
09756-48020  


e.

Push the release button on SST with the brake pedal depressed.

SST
09756-48020  

CAUTION:

The vehicle may suddenly move when the parking brake is released. Make sure to perform the release operation with the brake pedal depressed.


NOTICE:
·

After the FINISHED light illuminates on SST (09756-48070), do not perform the operation again.

·

If the release button on SST (09756-48020) is pressed more than twice at a time, it may damage the parking brake assembly.



HINT:
·

Confirm that the parking brake is operating by listening for operation sounds.

·

The parking brake may not release if the auxiliary battery voltage is too low. In this case, perform the release operation again using a fully charged or new auxiliary battery.




f.

When the FINISHED light of SST illuminates, release the brake pedal.

SST
09756-48020  


g.

Move the vehicle forward and rearward to check that the parking brake is released.

CAUTION:

Be careful when performing this operation. The vehicle may suddenly move.


NOTICE:
C450130

·

When moving the vehicle after the forced release of the parking brake, check that the connector shown in the illustration is disconnected.

·

The brake warning light (yellow) turns on when the vehicle is moved with the connector shown in the illustration disconnected.

·

Make sure to enter the diagnostic mode and clear the DTCs after performing the procedures.

·

If the DTCs are cleared but do not disappear:

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>FAIL-SAFE CHART