Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › FRONT CAMERA SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0455729 FRONT CAMERA SYSTEM Y

ADVANCED DRIVER ASSISTANCE SYSTEM  FRONT CAMERA SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the front camera system, perform troubleshooting for the pre-collision system.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a pre-collision system related warning message is displayed on the multi-information display, refer to How to Proceed with Troubleshooting for the pre-collision system.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Use the following procedure to troubleshoot the front camera system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Interview the customer and confirm the problem.


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage.

Standard voltage:

11 to 14 V (Ignition switch off)


HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Using the GTS, check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

b.

If a DTC is output, record the DTC.


Result:
Result Proceed to
DTCs are not output A
DTC C1AA800 is output B
DTC other than C1AA800 is output C



A

7.CHECK VEHICLE CONTROL HISTORY*

B

GO TO DIAGNOSTIC TROUBLE CODE CHART (C1AA800)

C

6.RECONFIRM DTC OUTPUT*
6.RECONFIRM DTC OUTPUT*
a.

Using the GTS, clear the DTCs.

Chassis > Front Recognition Camera > Clear DTCs
50002 430

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Using the GTS, check for DTCs.

Chassis > Front Recognition Camera > Trouble Codes
50001 430

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.CHECK VEHICLE CONTROL HISTORY*

B

7.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Front Recognition Camera > Utility
Tester Display
Vehicle Control History (RoB)
50005 430 55

b.

Make a note of the output Vehicle Control History (RoB).


Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) other than X2015 and X201C is output B
Vehicle Control History (RoB) X2015 or X201C is output C



A

B

8.RECONFIRM VEHICLE CONTROL HISTORY*

C

GO TO VEHICLE CONTROL HISTORY (X2015 or X201C)

8.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Front Recognition Camera > Utility
Tester Display
Vehicle Control History (RoB)
50005 430 55

b.

Using the GTS, check for Vehicle Control History (RoB).

Chassis > Front Recognition Camera > Utility
Tester Display
Vehicle Control History (RoB)
50005 430 1055

Result:
Result Proceed to
Vehicle Control History (RoB) is not output A
Vehicle Control History (RoB) is output B



A

B