Use these procedures to troubleshoot the pre-collision system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Interview the customer and confirm the problem.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage.
11 to 14 V (Ignition switch off)
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.
If more than one warning message is displayed, check in the order of A, B, C, D and E.
| Result | Proceed to |
|---|---|
| "VSC Turned OFF Pre-Collision Brake System Unavailable" is displayed | A |
| "Pre-Collision System Malfunction Visit Your Dealer" is displayed | B |
| "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed | C |
| Any of the following messages is displayed:
·
"Pre-Collision System Unavailable See Owner's Manual" ·
"Pre-Collision System Out of Temperature Range Unavailable See Owner's Manual" ·
"Pre-Collision System Radar In Self Calibration Unavailable See Owner's Manual" ·
"Front Camera Out of Temperature Range Unavailable Wait until Normal Temperature" ·
"Front Camera Low Visibility Unavailable See Owner's Manual" ·
"Front Camera Unavailable See Owner's Manual" |
D |
| Pre-collision system warning message is not displayed | E |
A
B
C
D
E
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC (C142571) is output | B |
| A DTC other than (C142571) is output | C |
A
B
C
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
If the Vehicle Control History (RoB) is output, record it.
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history (X2013, X2015, X2022, X2025, X2026 or X2028) is output | B |
| Vehicle control history other than (X2013, X2015, X2022, X2025, X2026 and X2028) is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle Control History (RoB) is not output | A |
| Vehicle Control History (RoB) is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using the GTS, clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Using the GTS, check if the DTCs are output again.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check whether the millimeter wave radar sensor assembly and surrounding area is dirty or obstructed by foreign matter.
Check that the following situations do not occur.
A cover other than the radar sensor cover is not installed
There is no dirt on the surrounding area of the radar or radar sensor cover
An accessory, such as bull bars, a grille guard, etc., which interferes with millimeter radio waves is installed
There is no coating, sticker, or painting applied to the radar sensor cover
There is no foreign matter between the radar and radar sensor cover
Clean away any dirt or foreign matter that is adhering to the area around the millimeter wave radar sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Before inspecting the multi-information display, be sure to first turn the ignition switch off and then to ON again.
Turn the ignition switch off.
Turn the ignition switch to ON.
Check whether "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" is displayed on the multi-information display.
| Result | Proceed to |
|---|---|
| Not displayed | A |
| Displayed | B |
A
B
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
Using the GTS, read the following Data List item for the front radar sensor system.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| On-Line Calibration Angle (Horizontal) | Calibrated angle value (horizontal) | -12.8 to 12.7 deg | Learned value | - |
| Tester Display |
|---|
| On-Line Calibration Angle (Horizontal) |
The value displayed is less than -0.5 to 0.5 deg.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
Explain to the customer that the "Pre-Collision System Radar Sensor Blocked Unavailable Clean Radar Sensor" message on the multi-information display was caused by dirt or foreign matter adhering to the area around the millimeter wave radar sensor assembly, and that the situation has been corrected.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Check the condition of the PCS warning light.
| Result | Proceed to |
|---|---|
| Only the PCS warning light is illuminated | A |
| The PCS warning light is not illuminated | B |
A
B
Check for vehicle control history and note any codes that are output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Check detection condition for the confirmed pre-collision system DTC.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>FAIL-SAFE CHART
| Proceed to |
|---|
| NEXT |
NEXT
Explain to the customer the cause of the previously stored DTC and that the output reason has been cleared.
Check for vehicle control history and note any codes that are output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Record the vehicle control history.
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history is output | B |
A
B
Check the conditions when pre-collision system operates or does not operate.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>PRECAUTION
| Result | Proceed to |
|---|---|
| No condition is met | A |
| Any condition is met | B |
A
B
Before performing beam axis adjustment, check the fitting of the front bumper cover and radiator grille assembly and confirm that there is no warping or deformation.
Adjust the reflector height.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Place the reflector.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Turn the cruise control main switch on.
Check the amount of misalignment and make a note.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
| Vertical | -5.0 to 5.0 deg. |
| Horizontal | -0.5 to 0.5 deg. |
| Result | Proceed to |
|---|---|
| Front beam axis misalignment value is within the specified range | A |
| Front beam axis misalignment value is not within the specified range | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
Check for vehicle control history and note any codes that are output.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Based on the customer's inquiry, check the corresponding factors in the vehicle control history, such as the detection time and date, trip information and elapsed time.
| Proceed to |
|---|
| NEXT |
NEXT
Explain to the customer the cause of the previously stored vehicle control history and that the output reason has been cleared.
After the explanation, make sure to clear vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |