Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0455732 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the EV control ECU. The EV control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the EV control ECU determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the EV control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

EV control ECU


Radar Cruise1 A

WIRING DIAGRAM

C454925E01
2.115,1.198 2.729,1.396 0.615,0.198 10 false STOP 1.958,0.635 2.906,0.833 0.948,0.198 10 false IG2 D NO.3 0.573,1.042 1.448,1.656 0.875,0.615 10 false from Auxiliary Battery 0.375,0.49 1.563,0.833 1.188,0.344 10 false from IG2 D Relay 3,0.49 3.156,0.688 0.156,0.198 10 false B 3,1.042 3.156,1.24 0.156,0.198 10 false B 2.781,0.365 2.938,0.563 0.156,0.198 10 false 5 2.781,0.917 2.938,1.115 0.156,0.198 10 false 1 3.771,1.219 3.927,1.417 0.156,0.198 10 false 3 3.375,1.344 3.875,1.531 0.5,0.188 10 false GND 2.479,1.615 2.813,1.802 0.333,0.188 10 false A3 2.469,1.771 4.333,2.156 1.865,0.385 10 false Stop Light Switch Assembly 3.552,1.052 3.708,1.25 0.156,0.198 10 false L 3.563,0.5 3.719,0.698 0.156,0.198 10 false L 3.781,0.917 3.938,1.115 0.156,0.198 10 false 2 3.781,0.365 3.938,0.563 0.156,0.198 10 false 4 5.677,1.052 6.135,1.25 0.458,0.198 10 false STP 5.677,0.5 6.135,0.698 0.458,0.198 10 false ST1- 5.26,0.49 5.719,0.688 0.458,0.198 10 false A16 2.229,2.792 2.688,2.99 0.458,0.198 10 false G102 2.229,2.969 3.969,3.51 1.74,0.542 10 false No. 2 Semiconductor Power Integration ECU 3.167,2.583 3.625,2.781 0.458,0.198 10 false STP 3.563,2.479 4.021,2.677 0.458,0.198 10 false 10 5.271,2.823 5.729,3.021 0.458,0.198 10 false G37 1.896,4.406 4.313,5.052 2.417,0.646 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.906,4.219 2.365,4.417 0.458,0.198 10 false A5 3.177,4 3.635,4.198 0.458,0.198 10 false STP 5.677,2.583 6.135,2.781 0.458,0.198 10 false STP1 5.344,0.813 5.802,1.01 0.458,0.198 10 false 7 5.333,0.24 5.792,0.438 0.458,0.198 10 false 1 5.406,2.479 5.865,2.677 0.458,0.198 10 false 25 3.573,3.896 4.031,4.094 0.458,0.198 10 false 37 5.271,2.99 6.802,3.531 1.531,0.542 10 false Certification ECU (Smart Key ECU Assembly) 5.031,4.229 5.49,4.427 0.458,0.198 10 false A6 5.677,4.01 6.135,4.208 0.458,0.198 10 false STP 5.396,5.302 5.854,5.5 0.458,0.198 10 false 18 5.708,1.479 7.01,1.854 1.302,0.375 10 false EV Control ECU 5.26,1.042 5.719,1.24 0.458,0.198 10 false A17 5.021,4.396 6.938,4.948 1.917,0.552 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.396,3.896 5.854,4.094 0.458,0.198 10 false 11 5.677,5.469 6.135,5.667 0.458,0.198 10 false STP 5.469,5.99 6.885,6.333 1.417,0.344 10 false Shift Control ECU 5.479,5.802 5.938,6 0.458,0.198 10 false D93

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the EV control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A3 stop light switch assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-1 (B) - Body ground Ignition switch off 11 to 14 V
A3-5 (B) - Body ground Ignition switch ON 11 to 14 V
A3-5 (B) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the A3 stop light switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A3)Location & Routing

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

A3-3 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the A16 and A17 EV control ECU connectors.


b.

Disconnect the A3 stop light switch assembly connector.


c.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


f.

Disconnect the G37 certification ECU (smart key ECU assembly) connector.


g.

Disconnect the D93 shift control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A3,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A3)Instrument Panel>Front Compartment Main Wire>Stop Light Switch Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-1 (ST1-) - A3-4 (L) Always Below 1 Ω
A17-7 (STP) - A3-2 (L) Always Below 1 Ω
A16-1 (ST1-) or A3-4 (L) - Body ground Always 10 kΩ or higher
A17-7 (STP) or A3-2 (L) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR