Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ROAD SIGN ASSIST SYSTEM
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0455734 ROAD SIGN ASSIST SYSTEM Y

ADVANCED DRIVER ASSISTANCE SYSTEM  ROAD SIGN ASSIST SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the road sign assist system, make sure that the pre-collision system and lane tracing assist system are not malfunctioning.

Pre-collision system: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Lane tracing assist system: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>LANE TRACING ASSIST SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Perform the following procedure to troubleshoot the road sign assist system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Interview the customer and confirm the problem.


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage.

Standard voltage:

11 to 14 V (Ignition switch off)


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTCs*

NG

5.CHECK FOR DTCs*
a.

Using the GTS, check for DTCs.

Body Electrical > Road Sign Assist > Trouble Codes
50001 431

b.

Make a note of the output DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK VEHICLE CONTROL HISTORY*

B

8.RECONFIRM DTC OUTPUT*
6.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for vehicle control history (RoB).

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55

b.

Make a note of the output vehicle control history (RoB).


Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) is output B



A

B

7.RECONFIRM VEHICLE CONTROL HISTORY*
7.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the vehicle control history (RoB).

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55

b.

Using the GTS, check for vehicle control history (RoB).

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55

Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) is output B



A

B

8.RECONFIRM DTC OUTPUT*
a.

Using the GTS, clear the DTCs.

Body Electrical > Road Sign Assist > Clear DTCs
50002 431

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ROAD SIGN ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Using the GTS, check for DTCs.

Body Electrical > Road Sign Assist > Trouble Codes
50001 431

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK VEHICLE CONTROL HISTORY*

B