Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM
RM37H0E _53 Suspension _097405 FRONT SUSPENSION _0455868 FRONT UPPER SUSPENSION ARM A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C448091N02
3.823,2.167 4.156,2.167 true 6.333,3 6.167,3 6.167,3 5.917,3.333 true 1.083,2.583 1.417,2.583 true 1.167,0.583 1.333,0.583 1.333,0.583 1.552,0.823 true 3.771,0.479 4.167,0.25 4.167,0.25 4.333,0.25 true 2.5,4.333 2.5,4.667 2.5,4.667 2.333,4.667 true 2.417,5.25 2.729,5.25 true 4.021,3.938 4.021,4.25 4.021,4.25 4.188,4.25 true 2.469,1.865 2.781,2.063 0.313,0.198 10 false x 2 4.25,1.083 4.563,1.281 0.313,0.198 10 false x 2 2.167,4.604 2.385,4.823 0.219,0.219 10 false ● 4.271,4.188 4.49,4.406 0.219,0.219 10 false ● 6.417,2.854 6.667,3.167 0.25,0.313 18 false 1 2.198,5.115 2.417,5.417 0.219,0.302 18 false 2 0.917,0.458 1.135,0.76 0.219,0.302 18 false 3 4.427,0.104 4.646,0.406 0.219,0.302 18 false 4 0.885,2.448 1.104,2.75 0.219,0.302 18 false 5 4.24,2.021 4.458,2.323 0.219,0.302 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT WHEEL - - - -
2 STEERING KNUCKLE ASSEMBLY LH 43212 (Click here) - -
3 FRONT UPPER NO. 1 ARM BRACKET LH 48657C - - -
4 FRONT UPPER NO. 2 ARM BRACKET LH 48658B - - -
5 FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH 48630D - - -
6 FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH 48630E - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front upper suspension arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assisr ECU initilization

·

Adjust sttering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 43212 2.DISCONNECT STEERING KNUCKLE LH

a.
C452110C01
0.969,1.063 0.833,0.833 0.833,0.833 0.583,0.833 true 1.104,1.604 0.833,1.833 0.833,1.833 0.667,1.833 true 5.313,3.292 5.604,3.5 5.604,3.5 5.344,3.24 true 5.833,2.833 5.667,2.833 5.667,2.833 5.406,2.969 true 5.333,2.583 5.167,2.583 5.167,2.583 4.969,2.813 true 4.698,3.375 4.667,3.583 4.667,3.583 4.5,3.583 true 4.51,2.885 4.333,2.667 4.333,2.667 4.167,2.667 true 2.271,2.5 2.688,2.5 true 2.917,3.583 2.75,3.583 2.75,3.583 2.604,3.469 true 4.875,5.281 4.75,5.49 4.75,5.49 4.833,5.25 true 4.729,4.979 4.5,4.833 4.5,4.833 4.417,4.833 true 4.917,4.417 5.083,4.417 5.083,4.417 5.198,4.792 true 6,4.604 5.833,4.604 5.833,4.604 5.656,4.854 true 5.448,5.385 5.583,5.583 5.583,5.583 5.75,5.583 true 3.167,5.583 3.031,5.583 3.031,5.583 2.948,5.417 true 3.333,4.917 3,4.917 true 0.365,0.74 0.552,0.927 0.188,0.188 10 true *a 0.479,1.75 0.708,1.906 0.229,0.156 10 false *b 0.083,0.083 0.292,0.365 0.208,0.281 18 true i 4.167,0.104 4.406,0.448 0.24,0.344 18 false ii 1,2.188 1.552,2.51 0.552,0.323 18 false iii, iv 0.979,4.198 1.563,4.563 0.583,0.365 18 false v, vi 5.667,3.438 5.896,3.594 0.229,0.156 10 false *c 4.26,5.146 4.49,5.302 0.229,0.156 10 false *d 5.885,2.75 6.115,2.906 0.229,0.156 10 false *e 5.375,2.5 5.604,2.656 0.229,0.156 10 false *f 4.323,3.49 4.552,3.646 0.229,0.156 10 false *g 3.979,2.594 4.208,2.75 0.229,0.156 10 false *h 4.188,3.073 4.417,3.229 0.229,0.156 10 false *i 2.74,2.417 2.958,2.604 0.219,0.188 10 true *j 2.979,3.49 3.333,3.708 0.354,0.219 10 true SST 4.625,5.49 4.854,5.646 0.229,0.156 10 false *c 5.729,3.146 5.958,3.302 0.229,0.156 10 false *d 4.229,4.75 4.458,4.906 0.229,0.156 10 false *e 4.76,4.323 4.99,4.479 0.229,0.156 10 false *f 6.042,4.531 6.271,4.688 0.229,0.156 10 false *h 5.802,5.5 6.031,5.656 0.229,0.156 10 false *g 5.854,5.083 6.083,5.24 0.229,0.156 10 false *i 3.229,5.5 3.583,5.719 0.354,0.219 10 true SST 3.375,4.823 3.594,5.01 0.219,0.188 10 true *j
*a Wooden Block *b Jack
*c SST (Spacer B) *d 1 mm (0.0394 in.)
*e Spacer *f Center Nut
*g Body *h Claw
*i Parallel *j String


i.

Support the front suspension lower arm assembly LH using a jack and wooden block.


ii.

Remove the 2 clips and 2 nuts.


iii.

Install 2 SST (spacer B) onto the front upper No. 1 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iv.

Using SST, disconnect the steering knuckle assembly LH from the front upper No. 1 suspension arm assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.




v.

Install 2 SST (spacer B) onto the front upper No. 2 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




vi.

Using SST, disconnect the steering knuckle assembly LH from the front upper No. 2 suspension arm assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





Hide 48657C 3.REMOVE FRONT UPPER NO. 1 ARM BRACKET LH

a.
C448097


Hide 48658B 4.REMOVE FRONT UPPER NO. 2 ARM BRACKET LH

a.
C448098


Hide 48630D 5.REMOVE FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C448099


Hide 48630E 6.REMOVE FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C448100