Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455873 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

C447144N02
3.75,0.75 3.75,0.25 3.75,0.25 3.917,0.25 true 6,1.75 6,1.25 6,1.25 6.167,1.25 true 2.25,0.667 2.25,0.333 2.25,0.333 2.417,0.333 true 2.948,2.906 3.365,2.906 true 2.583,3.365 3.104,3.583 0.521,0.219 10 false x 2 4.594,2.25 4.917,2.438 0.323,0.188 10 false x 3 3.594,1.51 3.99,1.719 0.396,0.208 10 false x 11 3.583,2.146 3.948,2.365 0.365,0.219 10 false x 4 2.49,0.188 2.771,0.542 0.281,0.354 18 false 1 6.26,1.083 6.542,1.438 0.281,0.354 18 false 2 3.448,2.75 3.729,3.104 0.281,0.354 18 false 3 3.969,0.115 4.25,0.469 0.281,0.354 18 false 4 4.042,1.917 4.365,2.104 0.323,0.188 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PACKAGE TRAY TRIM PANEL ASSEMBLY 64330 - - -
2 REAR TIRE - - - -
3 ROCKER PANEL MOULDING PROTECTOR LH 75866E - - -
4 REAR WHEEL HOUSE LINER LH 65638 - - -

C447145N03
2.667,0.333 2.917,0.333 true 1.01,2.667 1.177,2.667 1.177,2.667 1.177,3.156 true 3.344,1.792 3.594,1.792 true 1.677,3.313 1.875,3.313 true 2.594,2.563 2.76,2.563 2.76,2.563 2.76,3.052 true 2.24,3.167 2.521,3.521 0.281,0.354 18 false 5 2.385,0.198 2.667,0.552 0.281,0.354 18 false 6 4.01,1.646 4.292,2 0.281,0.354 18 false 7 0.708,2.594 0.979,2.76 0.271,0.167 10 false *1 3.406,0.458 3.719,0.656 0.313,0.198 10 false x 3 2.365,2.469 2.573,2.677 0.208,0.208 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR STABILIZER LINK ASSEMBLY LH 48840A (Click here) - -
6 REAR SHOCK ABSORBER CAP LH 48554A - - -
7 REMOVE REAR SHOCK ABSORBER WITH COIL SPRING - (Click here) - -

*1 FRONT STABILIZER BAR - -
● Non-reusable part - -

C447146N01
1.99,1.646 2.24,1.646 true 2.125,3.281 2.375,3.281 true 5.354,1.146 5.604,1.146 true 5.427,2.875 5.844,2.875 true 1.802,0.604 2.052,0.604 true 6.292,2.729 6.615,3.073 0.323,0.344 18 false 8 2.823,3.135 3.104,3.49 0.281,0.354 18 false 9 6.094,0.969 6.51,1.313 0.417,0.344 18 false 10 2.333,1.552 2.729,1.74 0.396,0.188 10 false *1 2.115,0.521 2.583,0.719 0.469,0.198 10 false ●*2

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR SHOCK ABSORBER ASSEMBLY LH 48540 (Click here) - -
9 REAR COIL SPRING LH 48231B (Click here) - -
10 REAR LOWER COIL SPRING INSULATOR LH 48258C (Click here) - -

*1 REAR SUSPENSION SUPPORT ASSEMBLY LH *2 LOCK NUT
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear shock absorber removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)


HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 64330 1.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 2.REMOVE REAR TIRE

Hide 75866E 3.REMOVE ROCKER PANEL MOULDING PROTECTOR LH

Hide 65638 4.REMOVE REAR WHEEL HOUSE LINER LH

Hide 48840A 5.REMOVE REAR STABILIZER LINK ASSEMBLY LH

a.
C447147N01
0.396,0.052 0.688,0.375 0.292,0.323 18 true i 3.885,0.021 4.229,0.344 0.344,0.323 18 true ii

i.

Remove the nut and rear stabilizer link assembly LH from the rear stabilizer bar.

HINT:

If the ball joint turns together with the nut, use a hexagon socket wrench 6 mm to hold the stud bolt.



ii.

Remove the bolt, nut and rear stabilizer link assembly LH from the rear No. 2 suspension arm assembly LH.



Hide 48554A 6.REMOVE REAR SHOCK ABSORBER CAP LH

a.
C447149


Hide 7.REMOVE REAR SHOCK ABSORBER WITH COIL SPRING

a.
C447150N01
2.594,0.063 2.802,0.396 0.208,0.333 18 true i

i.

Loosen the lock nut.

CAUTION:
C320511

·

Only loosen the lock nut, do not remove it.

·

If the lock nut is removed with the rear coil spring under tension, components of the rear shock absorber with coil spring may fly off.



NOTICE:

If the rear shock absorber with coil spring will not be disassembled, do not loosen the lock nut.




b.
C447151


c.
C447152C01
4.25,0.042 4.677,0.385 0.427,0.344 18 true ii 0.208,0.042 0.635,0.385 0.427,0.344 18 true i
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


i.

Remove the nut from the rear shock absorber with coil spring (lower side).


ii.

Remove the rear shock absorber with coil spring and washer as shown in the illustration.



Hide 48540 8.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

a.
C447153N01
4.177,1.031 4.177,0.531 4.177,0.531 4.344,0.531 true 4.417,0.448 4.875,0.646 0.458,0.198 10 false SST 2.24,0.052 2.656,0.427 0.417,0.375 18 true i, ii

i.

Secure SST in a vise.

SST
09727-30022  (09727-00010, 09727-00022, 09727-00031)


ii.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989C06
1.563,0.698 1.833,1.479 1.833,1.479 2.104,0.771 false 1.781,1.5 2.094,1.698 0.313,0.198 10 false *a
*a Rear Coil Spring Diameter


Do not perform the work without checking to make sure that the claws of the hooks are securely engaged.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C320512

Do not install SST to the rear coil spring unless its top and bottom hook distance is set to the widest condition.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C349511

Do not install SST when the distances between the SST arms or the number of coils of the coil spring between the hooks are not the same.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.





b.
C447154C01
3.479,0.51 2.396,0.958 2.396,0.958 2.958,0.531 true 4.333,1.083 4.75,1.333 4.75,1.333 4.917,1.333 true 4.573,0.865 5.073,0.865 true 4.479,0.688 5.083,0.167 5.083,0.167 4.135,0.792 true 2.208,0.073 2.917,0.385 0.708,0.313 18 false i - iii 2.094,0.844 2.438,1.063 0.344,0.219 10 false *b 4.958,1.26 5.417,1.458 0.458,0.198 10 false SST 5.135,0.792 5.594,0.99 0.458,0.198 10 false SST 5.146,0.083 5.49,0.302 0.344,0.219 10 false *a
*a Vehicle Nut *b Stopper Pin


i.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990C02
1.813,1.688 1.813,1.271 false 3.25,1.698 3.25,1.281 false 3.188,1.708 3.406,1.917 0.219,0.208 10 false *a 1.74,1.708 2.052,1.906 0.313,0.198 10 false *a
*a Stopper Pin


Do not perform the work if the stopper pin is not securely installed.



ii.

Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


iii.

Using SST, compress the coil spring.

SST
09727-00110  

CAUTION:
·
C320518

While compressing the spring, if the rear coil spring starts to bend into a bow shape, do not continue the work.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C320520

Do not compress the springs so far that the coils of the springs touch each other.

·

It could cause the hook to slip off and the spring to fly out, which could result in an injury.

·
C320522

Do not use an impact wrench.

·

The threads may be stripped, or the sudden compression may result in slack that causes the hooks to slip off, causing the spring to fly out and possibly resulting in injury.

·
C320524C01
1.021,3.104 1.698,3.104 true 0.844,3.021 1.156,3.177 0.313,0.156 10 false *a
*a Coil Spring Stopper Belt


If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.





c.

Check that the rear coil spring has become free, and remove the rear support to rear shock absorber lock nut.

CAUTION:
C320525

·

If the rear coil spring has not become free, do not remove the rear support to rear shock absorber lock nut.

·

The spring force will cause the components to be scattered, possibly resulting in injury.




d.
C438842N02
0.396,0.073 0.677,0.427 0.281,0.354 18 false i

i.

Check that the rear coil spring has become free, and remove the rear support to rear shock absorber lock nut.

CAUTION:
·
C320525

If the rear coil spring has not become free, do not remove the rear support to rear shock absorber lock nut.

·

The spring force will cause the components to be scattered, possibly resulting in injury.





e.
C447155C01
5.417,0.333 4,0.333 true 3.385,0.823 1.969,0.823 true 1.667,0.75 1.979,0.906 0.313,0.156 10 false *a 5.469,0.271 5.781,0.427 0.313,0.156 10 false *b 2.198,0.063 2.781,0.385 0.583,0.323 18 false i
*a Rear Shock Absorber Assembly LH Claw *b End of Rear Upper Coil Spring Insulator


i.

Remove the rear suspension support assembly from the rear shock absorber assembly LH.

NOTICE:

Turn the rear suspension support assembly to disengage the end of the rear upper coil spring insulator from the rear shock absorber assembly LH claws.




f.
C449945


Hide 48231B 9.REMOVE REAR COIL SPRING LH

a.
C449943N01
2.24,0.073 2.594,0.385 0.354,0.313 18 false i

i.

Remove the rear coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.




Hide 48258C 10.REMOVE REAR LOWER COIL SPRING INSULATOR LH

a.
C438839