Home › Steering › STEERING COLUMN › HEATED STEERING WHEEL CONTROLLER
RM37H0E _55 Steering _095770 STEERING COLUMN _0456684 HEATED STEERING WHEEL CONTROLLER A

STEERING COLUMN  HEATED STEERING WHEEL CONTROLLER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C447816N03
4.333,1 4.542,0.708 4.542,0.708 4.708,0.708 true 5.99,2.5 6.156,2.5 6.156,2.5 6.323,2.167 true 5.052,3.26 4.885,3.26 4.885,3.26 4.781,3.042 true 4.813,0.583 5.094,0.938 0.281,0.354 18 false 1 5.396,3.135 5.677,3.49 0.281,0.354 18 false 3 5.49,2.771 5.802,2.969 0.313,0.198 10 false x 2 6.865,0.938 7.104,1.146 0.24,0.208 10 false x 2 5.802,2.333 6.083,2.688 0.281,0.354 18 false 2 5.688,0.99 6,1.188 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING WHEEL ASSEMBLY 45100 - - -
2 STEERING PAD SWITCH ASSEMBLY 84250A - - -
3 STEERING VIBRATION AND HEATER ECU 864A2 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering vibration and heater ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 84250A 2.DISCONNECT STEERING PAD SWITCH ASSEMBLY

Hide 864A2 3.REMOVE STEERING VIBRATION AND HEATER ECU

a.
C447781C02
4.5,3.25 4.667,3.25 4.667,3.25 4.927,2.51 true 6.583,3.25 6.333,3.25 6.333,3.25 5.958,2.396 true 1.375,3.885 2.063,4.26 0.688,0.375 18 false iii, iv 0.167,0.146 0.521,0.531 0.354,0.385 18 false i 3.948,0.104 4.281,0.438 0.333,0.333 18 false ii 4.292,3.167 4.604,3.365 0.313,0.198 10 false *b 6.688,3.156 7,3.354 0.313,0.198 10 false *a
*a Heater Thermistor *b Thermostat
V113147

Remove in this Direction - -


i.

Disconnect each connector.


ii.

Remove the 3 screws and disconnect the steering wheel lower boss cover.

NOTICE:
·

Work carefully to prevent the heater thermistor and thermostat from coming off the steering wheel lower boss cover.

·

If the heater thermistor or thermostat come off the steering wheel lower boss cover, replace the steering wheel assembly.



HINT:

Only loosen the steering wheel lower boss cover. Do not remove it.



iii.

Remove the 2 screws.


iv.

Disconnect the connector and remove the steering vibration and heater ECU.