Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) D

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  OPERATION CHECK  


CHECK CUSTOMIZE PARAMETERS


NOTICE:

Confirm that the customize setting Auto Operation Interference Avoidance Function is set to off before checking the operation of the front power seat.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>CUSTOMIZE PARAMETERS



CHECK POWER SEAT FUNCTION (for Driver Seat)


a.

Check the basic functions. (for LHD)

i.
E457498C04
1.771,2.677 2.333,2.792 2.333,2.792 2.5,2.792 true 1.927,3.052 2.49,3.167 2.49,3.167 2.656,3.167 true 0.75,2.427 0.531,2.125 0.531,2.125 0.365,2.125 true 2.594,2.104 2.729,1.906 2.729,1.906 2.896,1.906 true 2.531,1.271 2.667,1.073 2.667,1.073 2.833,1.073 true 1.479,1.333 1.26,1.031 1.26,1.031 1.094,1.031 true 2.552,2.708 2.865,2.906 0.313,0.198 10 false *1 2.719,3.073 3.031,3.271 0.313,0.198 10 false *a 0.198,2.042 0.51,2.24 0.313,0.198 10 false *b 2.938,1.823 3.25,2.021 0.313,0.198 10 false *c 2.896,1.01 3.208,1.208 0.313,0.198 10 false *d 0.896,0.948 1.208,1.146 0.313,0.198 10 false *e
*1 Front power seat switch LH
*a Slide function
*b Front vertical function
*c Lifter function
*d Reclining function
*e Lumbar support adjustment function


Operate the front power seat switch LH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function

·

Lifter function

·

Front vertical function

·

Lumbar support adjustment function




b.

Check the basic functions. (for RHD)

i.
E450227C03
2.594,3.156 2.344,3.156 2.344,3.156 1.677,2.771 true 0.667,3.25 0.833,3.25 0.833,3.25 1.333,3.083 true 3.01,1.792 2.76,1.792 2.76,1.792 2.5,2.354 true 0.25,2.219 0.417,2.219 0.417,2.219 0.667,2.115 true 0.479,0.813 0.646,0.813 0.646,0.813 0.813,1.271 true 2.271,0.76 2.021,0.76 2.021,0.76 1.76,1.323 true 2.656,3.094 2.969,3.292 0.313,0.198 10 false *1 0.469,3.188 0.781,3.385 0.313,0.198 10 false *a 3.063,1.729 3.313,1.938 0.25,0.208 10 false *b 0.063,2.135 0.375,2.333 0.313,0.198 10 false *c 0.281,0.75 0.594,0.948 0.313,0.198 10 false *d 2.323,0.677 2.573,0.885 0.25,0.208 10 false *e
*1 Front power seat switch RH
*a Slide function
*b Front vertical function
*c Lifter function
*d Reclining function
*e Lumbar support adjustment function


Operate the front power seat switch RH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function

·

Lifter function

·

Front vertical function

·

Lumbar support adjustment function





CHECK POWER SEAT FUNCTION (for Front Passenger Seat)


a.
E462811C04
2.792,1.49 2.896,1.073 2.896,1.073 3.083,1.073 true 0.792,1.531 0.969,1.531 0.969,1.531 2.156,2.677 true 2.688,3.292 2.521,3.292 2.521,3.292 2.313,3.042 true 3.115,0.99 3.333,1.26 0.219,0.271 10 false *b 0.625,1.458 0.875,1.75 0.25,0.292 10 false *1 2.698,3.188 2.917,3.385 0.219,0.198 10 false *a
*1 Front power seat switch RH
*a Slide function
*b Reclining function


Check the basic functions. (for LHD)

i.

Operate the front power seat switch RH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function




b.
E462812C04
0.958,3.271 1.094,3.271 1.094,3.271 1.375,3.104 true 0.354,0.833 0.479,0.833 0.479,0.833 0.854,1.281 true 2.354,3.156 2.24,3.156 2.24,3.156 1.594,2.792 true 0.792,3.188 1.021,3.323 0.229,0.135 10 false *a 0.188,0.771 0.448,1.042 0.26,0.271 10 false *b 2.396,3.094 2.635,3.271 0.24,0.177 10 false *1
*1 Front power seat switch RH
*a Slide function
*b Reclining function


Check the basic functions. (for RHD)

i.

Operate the front power seat switch LH and check that the following seat functions operate properly:

·

Slide function

·

Reclining function





CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION (for Driver Seat)


*1: for LHD

*2: for RHD


a.
E450366C02
0.615,0.25 0.771,0.25 0.771,0.25 1.26,0.531 true 0.906,1.438 1.063,1.438 1.063,1.438 1.448,1.135 true 1.344,1.938 1.5,1.938 1.5,1.938 1.771,1.719 true 0.406,0.167 0.615,0.323 0.208,0.156 10 false *a 0.719,1.375 0.99,1.542 0.271,0.167 10 false *b 1.156,1.865 1.365,2.021 0.208,0.156 10 false *c
*a M1 Switch
*b M2 Switch
*c SET Switch


Check memorization and return operation

HINT:

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.


i.

Turn the ignition switch to ON and check that the P position indicator is on.


ii.

Move the seat to the foremost and uppermost positions using the front power seat switch LH*1 or RH*2.


iii.

Check that a buzzer sounds for 0.5 seconds and the seat position is memorized when the M1 switch is pressed within 3 seconds of the SET switch being pressed or the M1 switch is pressed while the SET switch is being pressed.


iv.

Move the seat out of the foremost and uppermost positions using the front power seat switch LH*1 or RH*2.


v.

Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M2 switch is pressed within 3 seconds of the SET switch being pressed or the M2 switch is pressed while the SET switch is being pressed.


vi.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves into the foremost and uppermost positions (memorized positions) when the M1 switch is pressed.


vii.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves out of the foremost and uppermost positions (memorized positions) when the M2 switch is pressed.


viii.

Turn the ignition switch off and open the driver door. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position by pressing the M1 or M2 switch within 180 seconds after the ignition switch is turned off.


ix.

Turn the ignition switch off and close the driver door. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position by pressing the M1 or M2 switch within 60 seconds after the ignition switch is turned off.


x.

Check that the buzzer sounds for 0.1 seconds and the seat moves to the stored position when either the M1 or M2 switch is pressed with the ignition switch ON and the shift position in P.




CHECK MEMORY CALL FUNCTION (for Driver Seat)


HINT:

Before checking the function, check that a memory call is registered.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


a.

Automatic memory call function

i.

While carrying the electrical key transmitter sub-assembly, unlock the driver door using the entry unlock function or wireless unlock operation. Open the driver door and check that a buzzer sounds for 0.1 seconds and the driver seat moves to the memorized position.




CHECK MEMORY CALL EMERGENCY STOP FUNCTION (for Driver Seat)


*1: for LHD

*2: for RHD


a.

While a memory call function is operating, check that performing one of the following will stop the memory call operation: 1) press the SET switch, M1 switch or M2 switch or 2) press the front power seat switch LH*1 or RH*2.



CHECK CHECK POWER EASY ACCESS FUNCTION (for Driver Seat)


NOTICE:

Perform this inspection with the customization function initialized to the default settings.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>CUSTOMIZE PARAMETERS


HINT:

The power easy access system may not operate if the seat position is near to the rear operating limit position when getting out of the vehicle.


a.

Auto-away function

i.

Under the following conditions, confirm that the seat will slide backward.

·

When the driver seat belt is unfastened with the ignition switch off and the shift position in P.

·

When the driver seat belt is unfastened with the shift position in P or N, and the ignition switch is turned from ON or ACC to off.




b.

Auto-return function

i.

Under the following conditions, confirm that the seat will slide forward.

·

When the driver seat belt is fastened with the ignition switch ACC or ON and the shift position in P or N.

·

When the driver seat belt is unfastened with the shift position in P or N, and the ignition switch is turned from off to ACC or ON.





CHECK POWER SEAT MOTOR


a.

Check the PTC operation inside the power seat motor.

NOTICE:

The inspection should be performed with the seat installed to the vehicle.


i.

Choose a power seat function. Operate a switch of the front power seat switch (LH or RH) and move the seat to the farthest possible position in one direction. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the switch of the front power seat switch (LH or RH) again and continue to try to move the seat in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

Approximately 4 to 90 seconds



iii.

After current has been cut (sound of the motor has stopped), operate the front power seat switch RH or LH again in that direction. Check that the current is cut off.


iv.

After current has been cut (sound of the motor has stopped), turn the front power seat switch RH or LH off and wait for approximately 60 seconds. Operate the same power seat switch and move the seat in the opposite direction. Check that the motor operates.




CHECK LUMBAR SUPPORT ADJUSTMENT MOTOR (for Driver Seat)


*1: for LHD

*2: for RHD


a.

Check the PTC operation inside the lumbar support adjustment motor.

NOTICE:

The inspection should be performed with the seat installed to the vehicle.


i.

Operate the front power seat switch LH*1 or RH*2 and move the lumbar support to either the foremost or rearmost position. Keep the seat in that position for approximately 60 seconds.


ii.

Operate the front power seat switch LH*1 or RH*2 again and continue to try to move the lumbar support in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound stops).

Standard:

Approximately 4 to 90 seconds



iii.

After current has been cut (sound of the motor has stopped), operate the front power seat switch LH*1 or RH*2 again in that direction. Check that the current is cut off.


iv.

After current has been cut (sound of the motor has stopped), turn the front power seat switch LH*1 or RH*2 off and wait for approximately 60 seconds. Operate the same power seat switch and move the seat in the opposite direction. Check that the motor operates.