Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU ASSEMBLY LH (for LHD)


E360013N40
4.99,0.333 5.49,0.583 0.5,0.25 2.5,0.333 3,0.583 0.5,0.25 1.479,0.333 1.979,0.583 0.5,0.25 5.125,0.375 5.521,0.635 0.396,0.26 10 false L43 2.635,0.365 3.063,0.625 0.427,0.26 10 false L42 1.625,0.385 2,0.625 0.375,0.24 10 false L41

a.

Disconnect the L41 and L43 position control ECU assembly LH connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
L41-2 (GND) - Body ground Body ground Always Below 1 Ω
L41-3 (+B) - Body ground Power source Ignition switch off 11 to 14 V
L43-1 (IG) - Body ground IG signal Ignition switch off → Ignition switch ON Below 1 V → 11 to 14 V
L43-15 (SYSB) - Body ground System power source Ignition switch off 11 to 14 V
L43-27 (DBCL) - Body ground Driver seat belt buckle switch signal Driver seat belt unfastened 10 kΩ or higher
Driver seat belt fastened Below 1 Ω
L43-28 (DRDC) - Body ground Tension reducer drive power source Ignition switch ON 11 to 14 V


c.

Reconnect the L41 and L43 position control ECU assembly LH connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L41-1 (SLD+) - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
L41-5 (SLD-) - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
L41-6 (LFT+) - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
L41-7 (FRV+) - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
L41-9 (L+) - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
L41-10 (RCL+) - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
L42-3 (L-) - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
L42-4 (FRV-) - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
L42-5 (LFT-) - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
L42-6 (RCL-) - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
L43-4 (LFLF) - Body ground Lumbar support adjuster switch (forward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
L43-6 (FRVU) - Body ground Front vertical switch (upward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
L43-7 (LFTU) - Body ground Rear lifter switch (upward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
L43-8 (RCLF) - Body ground Reclining switch (forward) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
L43-9 (SLDF) - Body ground Slide switch (forward) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
L43-12 (SGND) - Body ground Sensor ground Always Below 1 Ω
L43-18 (LFLR) - Body ground Lumbar support adjuster switch (rearward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
L43-20 (FRVD) - Body ground Front vertical switch (downward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
L43-21 (LFTD) - Body ground Rear lifter switch (downward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
L43-22 (RCLR) - Body ground Reclining switch (rearward) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
L43-23 (SLDR) - Body ground Slide switch (rearward) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L43-10 (SSFV) - Body ground Front vertical position signal Front vertical function operating Pulse generation
L43-11 (SSRR) - Body ground Reclining position signal Reclining function operating Pulse generation
L43-25 (SSRL) - Body ground Rear lifter position signal Rear lifter function operating Pulse generation
L43-26 (SSRS) - Body ground Slide position signal Slide function operating Pulse generation



CHECK POSITION CONTROL ECU ASSEMBLY RH (for RHD)


E360013N39
4.99,0.333 5.49,0.583 0.5,0.25 2.5,0.333 3,0.583 0.5,0.25 1.479,0.333 1.979,0.583 0.5,0.25 5.125,0.396 5.438,0.594 0.313,0.198 10 false L17 2.635,0.385 2.948,0.583 0.313,0.198 10 false L16 1.646,0.385 1.958,0.583 0.313,0.198 10 false L15

a.

Disconnect the L15 and L17 position control ECU assembly RH connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
L15-2 (GND) - Body ground Body ground Always Below 1 Ω
L15-3 (+B) - Body ground Power source Ignition switch off 11 to 14 V
L17-1 (IG) - Body ground IG signal Ignition switch off → Ignition switch ON Below 1 V → 11 to 14 V
L17-15 (SYSB) - Body ground System power source Ignition switch off 11 to 14 V
L17-27 (DBCL) - Body ground Driver seat belt buckle switch signal Driver seat belt unfastened 10 kΩ or higher
Driver seat belt fastened Below 1 Ω
L17-28 (DRDC) - Body ground Tension reducer drive power source Ignition switch ON 11 to 14 V


c.

Reconnect the L15 and L17 position control ECU assembly RH connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L15-1 (SLD+) - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
L15-5 (SLD-) - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
L15-6 (LFT+) - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
L15-7 (FRV+) - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
L15-9 (L+) - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
L15-10 (RCL+) - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
L16-3 (L-) - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
L16-4 (FRV-) - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
L16-5 (LFT-) - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
L16-6 (RCL-) - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
L17-4 (LFLF) - Body ground Lumbar support adjuster switch (forward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
L17-6 (FRVU) - Body ground Front vertical switch (upward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
L17-7 (LFTU) - Body ground Rear lifter switch (upward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
L17-8 (RCLF) - Body ground Reclining switch (forward) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
L17-9 (SLDF) - Body ground Slide switch (forward) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
L17-12 (SGND) - Body ground Sensor ground Always Below 1 Ω
L17-18 (LFLR) - Body ground Lumbar support adjuster switch (rearward) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 V
L17-20 (FRVD) - Body ground Front vertical switch (downward) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
L17-21 (LFTD) - Body ground Rear lifter switch (downward) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
L17-22 (RCLR) - Body ground Reclining switch (rearward) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
L17-23 (SLDR) - Body ground Slide switch (rearward) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
L17-10 (SSFV) - Body ground Front vertical position signal Front vertical function operating Pulse generation
L17-11 (SSRR) - Body ground Reclining position signal Reclining function operating Pulse generation
L17-25 (SSRL) - Body ground Rear lifter position signal Rear lifter function operating Pulse generation
L17-26 (SSRS) - Body ground Slide position signal Slide function operating Pulse generation



FRONT MULTIPLEX NETWORK DOOR ECU LH (for LHD)


B338775N42
3.333,0.25 3.833,0.5 0.5,0.25 3.448,0.281 4.021,0.635 0.573,0.354 10 false E25

a.

Disconnect the E25 front multiplex network door ECU LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-1 (GND) - Body ground Body ground Always Below 1 Ω
E25-3 (SIG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E25-4 (CPUB) - Body ground Battery power supply Ignition switch off 11 to 14 V
E25-6 (BDR) - Body ground Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E25 front multiplex network door ECU LH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-25 (MM) - E25-26 (MSWE) SET switch signal SET switch off 11 to 14 V
SET switch on Below 1 V
E25-22 (M1) - E25-26 (MSWE) M1 switch signal M1 switch off 11 to 14 V
M1 switch on Below 1 V
E25-23 (M2) - E25-26 (MSWE) M2 switch signal M2 switch off 11 to 14 V
M2 switch on Below 1 V
E25-26 (MSWE) - Body ground Ground Always Below 1 Ω



FRONT MULTIPLEX NETWORK DOOR ECU RH (for RHD)


B338775N41
3.333,0.25 3.833,0.5 0.5,0.25 3.5,0.313 3.833,0.49 0.333,0.177 10 false E7

a.

Disconnect the E7 front multiplex network door ECU RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-1 (GND) - Body ground Ground Always Below 1 Ω
E7-3 (SIG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
E7-4 (CPUB) - Body ground Battery power supply Ignition switch off 11 to 14 V
E7-6 (BDR) - Body ground Battery power supply Ignition switch off 11 to 14 V


c.

Reconnect the E7 front multiplex network door ECU RH connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-25 (MM) - E7-26 (MSWE) SET switch signal SET switch off 11 to 14 V
SET switch on Below 1 V
E7-22 (M1) - E7-26 (MSWE) M1 switch signal M1 switch off 11 to 14 V
M1 switch on Below 1 V
E7-23 (M2) - E7-26 (MSWE) M2 switch signal M2 switch off 11 to 14 V
M2 switch on Below 1 V
E7-26 (MSWE) - Body ground Ground Always Below 1 Ω



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E453982C14
1.083,3.198 1.49,3.458 0.406,0.26 3.24,3.198 3.646,3.458 0.406,0.26 5.448,3.208 5.854,3.469 0.406,0.26 3.24,7.708 3.646,7.969 0.406,0.26 1.823,4.542 2.229,4.802 0.406,0.26 5.385,4.479 5.792,4.74 0.406,0.26 1.125,6.177 1.531,6.438 0.406,0.26 3.573,6.115 3.979,6.375 0.406,0.26 6.25,6.146 6.656,6.406 0.406,0.26 5.271,6.146 5.677,6.406 0.406,0.26 1.625,1.781 1.906,1.781 false 1.625,1.427 1.906,1.427 false 1.625,1.115 1.906,1.115 false 1.573,0.604 1.573,0.24 1.573,0.24 1.781,0.24 false 1.99,1.729 2.302,1.927 0.313,0.198 10 false D14 1.979,1.063 2.292,1.26 0.313,0.198 10 false D12 1.99,1.375 2.302,1.573 0.313,0.198 10 false D11 3.75,0.927 3.906,1.125 0.156,0.198 10 false A 1.833,0.177 2.146,0.375 0.313,0.198 10 false *1 5.531,3.271 5.844,3.469 0.313,0.198 10 false D12 3.323,3.271 3.635,3.469 0.313,0.198 10 false D11 1.177,3.271 1.49,3.469 0.313,0.198 10 false D14 3.417,7.76 3.573,7.958 0.156,0.198 10 false A 0.833,1.031 1.146,1.229 0.313,0.198 10 false 4H 0.854,1.646 1.167,1.844 0.313,0.198 10 false 4F 0.854,2.01 1.167,2.208 0.313,0.198 10 false 4L 0.865,2.229 1.177,2.427 0.313,0.198 10 false 4K 5.823,1.042 6.135,1.24 0.313,0.198 10 false 4D 5.813,1.615 6.125,1.813 0.313,0.198 10 false 4A 1.958,4.615 2.271,4.813 0.313,0.198 10 false 4A 5.51,4.542 5.823,4.74 0.313,0.198 10 false 4D 1.271,6.24 1.583,6.438 0.313,0.198 10 false 4F 3.688,6.177 4,6.375 0.313,0.198 10 false 4H 6.417,6.208 6.729,6.406 0.313,0.198 10 false 4L 5.406,6.219 5.719,6.417 0.313,0.198 10 false 4K
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
A-32 (IG) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground Ground Always Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
D11-1 (FLCY) - Body ground Front door courtesy light switch assembly LH input Front left door open Below 1 V
Front left door closed 4.7 to 5.3 V
D11-6 (FRCY) - Body ground Front door courtesy light switch assembly RH input Front right door open Below 1 V
Front right door closed 4.7 to 5.3 V