Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › SERVICE PLUG GRIP
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457192 SERVICE PLUG GRIP A

HYBRID / BATTERY CONTROL  SERVICE PLUG GRIP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A477105N03
2.229,0.854 2.146,1.177 2.146,1.177 2.063,1.177 true 1.167,1.083 1.333,1.083 1.333,1.083 1.594,0.729 true 6.521,0.229 6.896,0.229 true 6.552,0.76 6.875,0.76 true 1.844,1.052 2.094,1.333 0.25,0.281 18 false 5 0.969,0.969 1.219,1.25 0.25,0.281 18 false 4 1.115,0.521 1.427,0.719 0.313,0.198 10 false x 2 6.094,0.104 6.625,0.427 0.531,0.323 18 false 1, 2 6.333,0.646 6.615,1 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CHECK FOR DTC - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 NO. 8 EV BATTERY SHIELD PANEL G92QAA - - -
5 SERVICE PLUG GRIP G3834 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during service plug grip removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A340386


·

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.CHECK FOR DTC

a.
A461168N04
0.479,0.073 0.76,0.427 0.281,0.354 18 false i

i.

Check for DTCs.

CAUTION:
·
A340380

Confirm that DTC P0AA649 (Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure), P1C7C49 (Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure), P1C7D49 (Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure), P1C7E49 (Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure), P1C7F49 (Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure), P1EEC49 (Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure), P1EED49 (Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure), P1EEE49 (Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure) or P1EEF49 (Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure) is not output before removing or installing the EV supply battery assembly. If this DTC is output, perform troubleshooting for this DTC first.

·

To reduce the risk of electric shock, do not perform troubleshooting before checking for DTCs.





Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide G92QAA 4.REMOVE NO. 8 EV BATTERY SHIELD PANEL

a.
A477170


Hide G3834 5.REMOVE SERVICE PLUG GRIP

Z101186

CAUTION:
·

Be sure to wear insulated gloves.

·
A484004

Do not inspect or service the high voltage system with the service plug grip and FC converter power outlet cable (inverter with converter assembly) installed.

·

To reduce the risk of electric shock, make sure to remove the service plug grip and FC converter power outlet cable (inverter with converter assembly) to cut off the high voltage circuit before servicing the vehicle.

·

Make sure to remove the service plug grip first, and then remove the FC converter power outlet cable (inverter with converter assembly).

·
A484005

To reduce the risk of electric shock, make sure to wait at least 10 minutes after removing the service plug grip and FC converter power outlet cable (inverter with converter assembly) to fully discharge the high voltage capacitor inside the inverter with converter assembly.

·

Keep the removed service plug grip in your pocket to prevent other technicians from accidentally installing it while you are servicing the vehicle.



NOTICE:
·

After removing the service plug grip and FC converter power outlet cable (inverter with converter assembly), turning the ignition switch to ON (READY) may cause a malfunction. Do not turn the ignition switch to ON (READY) unless instructed by the repair manual.

·

Do not touch the terminals of the service plug grip and FC converter power outlet cable (inverter with converter assembly).

·

If the service plug grip has been struck or dropped, replace it.



HINT:

Waiting for at least 10 minutes is required to discharge the high voltage capacitor inside the inverter with converter assembly.



a.
A477172N01
1.479,0.51 1.698,0.719 0.219,0.208 10 true 1 1.219,1.115 1.396,1.313 0.177,0.198 10 true 2 5.385,1.271 5.615,1.469 0.229,0.198 10 true 3 0.396,0.031 0.563,0.292 0.167,0.26 18 true i

i.

While wearing insulated gloves, rotate the handle of the service plug grip and remove the service plug grip as indicated by the arrows in the order shown in the illustration.