Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C12F812  ECB Solenoid Control "A" Circuit Short to Battery  C12F814  ECB Solenoid Control "A" Circuit Short to Ground or Open  


DESCRIPTION

The main relay is built into the No. 1 skid control ECU (brake booster with master cylinder assembly).

The main relay supplies power to the switching solenoid and the linear solenoid.

The main relay remains on for approximately 3 minutes after the ignition switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C12F812 ECB Solenoid Control "A" Circuit Short to Battery When there is a main relay off command from the ECU, 3.5 V or more is detected at terminal BS for 4.5 seconds or more.
·

Short in main relay circuit

·

Main relay internal stuck

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster A
·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System


C12F814 ECB Solenoid Control "A" Circuit Short to Ground or Open Either of the following is detected:
·

When the ignition switch is turned to ON (READY):

The BS terminal voltage is less than 3.3 V for 0.05 seconds or more, when the IG1 terminal voltage is 9.5 V or more and operation of the main relay is requested.

·

When the ignition switch is off:

The BS terminal voltage is less than 3.3 V for 0.05 seconds or more, when operation of the main relay is requested.


·

Open or short in main relay circuit

·

Wire harness and connector

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster A
·

Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

·

ECB: Electronically Controlled Brake System



C12F814 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the ignition switch is turned to ON (READY) ○ -
When the IG1 terminal voltage is 9.5 V or more ○ -
When the ignition switch is off - ○
Malfunction Status The BS terminal voltage is less than 3.3 V and operation of the main relay is requested ○ ○
Detection Time 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.READ VALUE USING GTS (BS VOLTAGE)
a.

Perform the Active Test and operate the main relay.


b.

Monitor the value of BS Voltage when the Active Test is being performed.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Main Relay Main relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS Voltage BS voltage value Min.: 0.0 V
Max.: 25.5 V
- Changes in proportion to auxiliary battery voltage
Chassis > Brake Booster > Active Test
Active Test Display
ECB Main Relay
Data List Display
BS Voltage
50004 466 41 313
HINT:

During the Active Test, the voltage indicated by BS Voltage changes in proportion to the voltage of the auxiliary battery.



Result:
Result Proceed to
During the Active Test, the voltage indicated by BS Voltage increases to the approximate voltage of the auxiliary battery. A
During the Active Test, the voltage indicated by BS Voltage remains low around 0 V. B



A

2.CLEAR DTC

B

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
C12F812 and C12F814 are not output A
C12F812 or C12F814 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-14 (+BI1) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-15 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR