Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C139100  Abnormal Leak in Accumulator  


DESCRIPTION

This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake booster with master cylinder assembly or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C139100 Abnormal Leak in Accumulator Either of the following is detected:
·

When the brake pedal is not depressed and the pump motor is operating, the accumulator pressure sensor value does not increase a certain number of times.

·

When the brake pedal is not depressed and the pump motor is not operating, the accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times.


·

Brake fluid leaks

·

Brake booster with master cylinder assembly

(Malfunctioning internal seal etc.)

·

Brake booster pump assembly

(Accumulator internal gas pressure decrease, etc.)


Brake Booster A Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

C139100 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the brake pedal is not depressed and the pump motor is operating ○ -
When the brake pedal is not depressed and the pump motor is not operating - ○
Malfunction Status The accumulator pressure sensor value does not increase a certain number of times ○ -
The accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.READ VALUE USING GTS (SERVO PRESSURE)
a.

Perform the Active Test and operate the linear solenoid (SLR) in the brake booster with master cylinder assembly.


b.

Check that the servo pressure output value does not increase when performing the Active Test.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid Start (Activate)
Solenoid SLR
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Check that park (P) is selected

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 466 42 210
OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:
·

If the servo pressure output value increases, an internal brake fluid leak in the brake booster with master cylinder assembly is suspected.

·

Perform the Active Test with the current set to maximum.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

2.CHECK OPERATING TIME OF PUMP MOTOR
2.CHECK OPERATING TIME OF PUMP MOTOR
a.

With the ignition switch is turned to ON (READY), check the operation of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
50003 466 96

Result:
Result Proceed to
The pump motor operates once or more within 20 seconds or operates for 10 seconds or more each time. A
Other than above. B



A

3.CHECK FOR FLUID LEAK

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK FOR FLUID LEAK
a.

Check that there are no leaks from the connections between the brake booster pump assembly, brake booster with master cylinder assembly and brake actuator assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



ii.

Turn the ignition switch off.


iii.

Disconnect the A2 brake pedal stroke sensor assembly connector.


iv.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


v.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B





A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE BOOSTER PUMP ASSEMBLY

for Brake Booster with Master Cylinder Assembly for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for Brake Booster with Master Cylinder Assembly for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL

for Brake Booster Pump Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL


B

REPAIR MALFUNCTIONING PART