This DTC is stored when the No. 2 skid control ECU (brake actuator assembly) receives a power supply malfunction signal from the steering sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| C14FE14 | Steering Angle Sensor Supply Voltage Circuit Short to Ground or Open | When the +BS terminal voltage is from 9.5 to 17.4 V, a steering sensor power supply malfunction signal is received from the steering sensor. | ·
Steering sensor ·
Wire harness and connector |
Brake/EPB | A | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
Refer to DTC C05262A.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C05262A
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C14FE14 is not output | A |
| C14FE14 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the D34 steering sensor connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D34)Location & Routingewd_type=routing;type=c;code=D34 Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensorewd_type=component;type=c;code=D34;pinno=9 |
||
| D34-9 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D34)Location & Routingewd_type=routing;type=c;code=D34 Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensorewd_type=component;type=c;code=D34;pinno=4 |
||
| D34-4 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D34)Location & Routingewd_type=routing;type=c;code=D34 Click Connector(D34)Instrument Panel>Instrument Panel Wire>Steering Sensorewd_type=component;type=c;code=D34;pinno=6 |
||
| D34-6 (ESS) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG